Publicidad
Idiomas disponibles
Idiomas disponibles
TO LEVEL
MOWER
Make
sure tires are properly
inflated to the
PSI shown
on tires. If tires are over or under
inflated, it may affect the appearance
of your
lawn and lead you to think the mower
is not
adjusted
properly.
VISUAL
SIDE-TO-SIDE
ADJUSTMENT
1.
With all tires properly
inflated
and if your
lawn
appears
unevenly
cut,
determine
which
side of mower
is cutting
lower.
NOTE:
As desired,
you can
raise
the low
side of mower
or lower
the high side.
2.
Go to side of mower
you wish to adjust.
3.
With a3/4" oradjustablewrench,turn
lift link
adjustment
nut (A) to the left to lower the
mower, or, to the right to raise the mower.
Turn nut rig
to raise mower
'..".Turn nut left
" to bower mower
NOTE:
Each full turn of adjustment
nut will
change
mower
height
about
3/16".
4.
Test your
adjustment
by mowing
some
uncut
grass
and visually
checking
the
appearance.
Readjust,
if necessary,
until
you are satisfied
with the results.
PRECISION
SIDE-TO-SIDE
ADJUSTMENT
1.
With all tires properly
inflated,
parktractor
on level ground
or driveway.
,_
CAUTION:
Blades
are sharp.
Protect
your
hands
with gloves
and/or
wrap
blade
with heavy
cloth.
2.
Raise mower
to its highest
position.
3.
At both sides of mower,
position
blade at
side and measure
the distance
(A) from
bottom
edge of blade to the ground.
The
distance
should be the same on both sides.
4. If adjustment
is necessary,
see steps 2
and 3 in Visual Adjustment
instructions
above.
5. Recheck measurements,
adjustifneces-
sary until both sides are equal.
FRONT-TO-BACK
ADJUSTMENT
IMPORTANT:
Deck must be level side-to-
side.
To obtain the best cutting results, the mower
blades should be adjusted so the front tip is
1/8" to 1/2" lower than the rear tip when the
mower is in its highest position.
_i, CAUTION:
Blades are sharp.
Protect
your hands with gloves and/or wrap blade
with heavy cloth.
• Raise mower to highest position.
• Position any blade so the tip is pointing
straight forward. Measure distance (B) to
the ground at front and rear tip of the blade.
OO
O
_
02548
• If front tip of blade is not 1/8" to 1/2" lower
than the rear tip, go to the front of tractor.
• With
an
11/16"
or adjustable
wrench,
loosen
jam
nut A several
turns
to clear
adjustment
nut B.
• With a 3/4" or adjustable
wrench,
turn front
link adjustment
nut (B) clockwise
(Itighten)
to raise the front of mower, or, counterclock-
wise
(loosen)
to lower
the
front
mower.
Tighten adjust nut
B to raise mower
....
-- J
Loosen adjust
nut B to lower
mower
Loosen jam nut A first
NOTE:
Each full turn of the adjustment
nut
will change
mower
height
about
1/8".
•
Recheck
measurements,
adjust
if neces-
sary until front tip of blade
is 1/8" to 1/2"
lower than the rear tip.
• Hold adjustment
nut in position with wrench
and tighten
jam nut securely
against
ad-
justment
nut.
24
Publicidad
