Cybex Silver PALLAS B3 Guia Del Usuario página 12

PRODUCT PARTS
EN
(1) Backrest
(2) Booster
(3) Impact shield (76 cm – 105 cm)
(4) ISOFIX adjustment handle
(5) ISOFIX locking arms
(6) ISOFIX anchorage points
(7) ISOFIX safety indicator
(8) Top tether belt
(9) Top tether safety indicator
(10) ISOFIX release buttons
(11) Adjustable headrest
(12) Adjustment handle of headrest
(13) Belt of the impact shield
INITIAL ASSEMBLY
Connect the backrest (1) to the booster (2) by hooking the guide lug on the
axis of the booster. The backrest (1) is then folded forward. Place the impact
shield (3) on the booster (2).
THE CORRECT POSITION IN THE VEHICLE
76 cm – 105 cm; > 15 m with impact shield
This is an i­Size Enhanced Child Restraint System. It is approved according
to UN Regulation No. R129/03, for use in i­Size compatible vehicle seating
positions as indicated by vehicle manufacturers in their vehicle user guides. If
your vehicle does not have an i­Size seating position, please check the vehicle
type list. You can obtain the most up­to­date version from go.cybex-online.
com/pallas-b3-isize-car-compatibility.
100 cm – 150 cm; with automatic three-point belt
The car seat can be used on vehicle seats which are equipped with an
automatic three­point belt. Refer to the vehicle type list for approved vehicles.
You can obtain the most up­to­date version from go.cybex-online.com/pallas-
b3-isize-car-compatibility.
For the use with three­point belt between the height range 100 cm – 150 cm
there is the possibility of usage without ISOFIX and top tether. In this case, the
car seat must always be secured with the three­point belt even when there is
no child in the seat.
8
(14) Belt adjuster release button
(15) Belt adjuster
(16) Buckle of the impact shield
(17) Tongue of the impact shield
(18) Lap belt guide (100 cm – 150 cm)
(19) Shoulder belt guide
(100 cm – 150 cm)
(20) Top tether adjustment button
(21) Belt release hook
(22) Metal bracket
(23) Linear Side­impact Protection
(L.S.P.)
In exceptional cases, the car seat may also be used on the front passenger
seat. Always comply with the recommendations of the vehicle manufacturer.
Above a child's height of 135 cm, the compatibility between the car seat and
��
your vehicle might be reduced.
INSTALLING THE CAR SEAT IN THE VEHICLE
1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Pull the ISOFIX adjustment handle (4) and pull out the ISOFIX locking
arm (5) with the other hand until it locks into position. Repeat the same for
releasing the ISOFIX locking arm (5) on the other side.
�� The ISOFIX locking arms have to be released independently.
3. Place the car seat on an appropriate seat in the car.
4. Push the ISOFIX locking arms (5) into the ISOFIX anchorage points (6)
until these lock into place with an audible "CLICK". The two ISOFIX safety
indicators (7) will switch from red to green.
5. Ensure the car seat is secure by trying to pull it out of the ISOFIX
anchorage points (6).
6. The car seat can be brought into different sitting or recline position
by pressing the ISOFIX adjustment handle (4) and moving the car
seat forward or push back. See chapter "ADJUSTING THE RECLINE
POSITIONS".
�� If the headrest of the vehicle is in the way, pull it upwards to its furthest
extent or remove it completely (except in rear­facing vehicle seats).
7. Guide the top tether belt (8) straight across the vehicle seat and anchor it
using the snap hook on the anchor point of your vehicle.
Top tether can be extended by pressing the top tether adjustment
��
button (20).
�� Pass the top tether belt underneath the car headrest. Never pass the top
tether belt over the car headrest.
8. Tighten the top tether belt (8) until the top tether safety indicator (9) turns
green.