Panasonic ES726 Instrucciones De Funcionamiento página 7

minutes
per
shave
for
a normal
beard).
You can
always
store
your
shaver
in
the charging adaptor
to maintain
full
power
capacity. This
shaver cannot
be overcharged.
Before
traveling,
charge
it
fully
for
8
hours
if
you
will
not
be
taking the
charging adaptor
with you.
For
a better
shave
Put a
thin
layer
ot
shaving
foam on
your face which works as
lubricator.
Do
not put a
thick layer of
shaving
foam
as
it
becomes
messy.
If
the
shaving
head
is
clogged
with
foam,
simply
rinse
it
under
running water.
Hold
the
shaver
at
a
right
angle
(90°)
to
your
skin (see
fig.
3).
Depress
the switch lock button
and
slide
the
On/Off
switch
upward
to
turn
the
shaver
on. Start out
shaving
by
applying gentle pressure
to
your
face.
Stretch your skin with
your
free
hand and
move
the
shaver back and
forth in
the
direction of
your
beard.
You may
gently
increase
the
amount
of
pressure as your
skin
becomes accustomed
to this
shaver. Applying
excessive
pres-
sure
does
not
provide
a
closer
shave and
may
irritate
skin.
System
outer
foil
and
lift
Strips
(see
fig.
4)
System
outer
foil
has
a
slit
blade
(a)
between two
foils (b),
and
a
lift
strips
(c)
on each
outside
of
the
foils.
They
move
up and
down
independently
to
follow
the contours
of
your
face.
The
lift
strips
lift
lying hairs
and
help
introduce the hairs into
the holes
of
foils to cut.
The
slit
blade catches
and
cuts longer
and
lying
hairs easi-
ly-
Using
the
trimmer
(see
fig.
5)
Slide the
trimmer handle up
to
the
*
position
until
it
clicks
in.
Place
the trimmer
at
a
right
angle
to
your
skin
and
move
it
downward
to
trim sideburns.
Cleaning your shaver
(see
fig. 6)
After
every shave, press
the
foil
frame
release button
to
pop open
the
foil
frame.
Turn
the
shaver on
and
rinse
the inner
blades under
running
water
or
in
a basin.
After
rinsing,
switch the
shaver
off
and
leave
it
to
dry without closing the
foil
frame and
the
protective
cap. After
the
shaving
head
dries,
close the
foil
frame and
replace the protective
cap on
the shaver.
Replacing shaving
head
components
With
daily
use,
the
outer
foil
may
need
to
be replaced every year
and
the inner blades every 2
years.
Replacing
the
system
outer
toil
(see
fig.
7)
Squeeze
the
system
outer
foil
release buttons
and
lift
the
system
outer
foil
upward
to
remove
it.
To
insert
the
new
system
outer
foil,
press
down
until
it
snaps
into
place.
Replacing
the inner blades
(see
fig. 8)
Press
the
foil
frame
release button
to
pop open
the
toil
frame.
Pull
the
foil
frame
vertically out
of
the upright
shaver.
Remove
the inner
blade
one
at
a
time
by
grasping
it
firmly at
both
ends and
pulling straight
away
from
7