Publicidad
The motor can be mounted in two different ways:
Mounting with horizontal hole (Fig.1a)
To mount the motor on existing shutters, drill the shaft horizontally.
1) Fix the gearmotor to the bar 2 using bracket 1 (if bar diameter is 48mm or 42mm use appropriate reduction
elements).
2) Lock the gearmotor on the bar by means of the screw 3, safety washer 4 and nut 5.
3) Fix the two crown gears 6 to the gearmotor by means of the screws 7 and self-locking nuts 8.
4) Make appropriate holes on the bar for the insertion of the wire 9 and electric cable sheath 10 making sure
that the position of the holes facilitates the insertion of the wires and cables.
Mounting with vertical hole (Fig.1b)
During installation of a new shutter the motor can be slid onto the shaft without dismantling the gear.
1) To vertically perforate the pipe, and using the clamp 11, to stop the motor on the pole using the screw 13
and the side screw 12.
2) On the flange you will find some places for the dice of block 14.
NB: In both cases always firmly tighten clamp 1 (Fig.1a).
1) Remove the limit switch cover.
2) With the roller shutter completely closed (down), set plastic wheel 1 in contact with closing limit switch.
3) Check that spacer 2 is fitted as indicated in the diagram.
4) Once made the connections, roll up the roller shutter up to the point of max. opening wanted.
5) Roll-down the roller shutter once again checking if the microswitch is activated at the wanted point; in the
negative, adjust it using plastic wheel 1 according to the sign + or -.
6) Remove the spacer 2 from the shaft and open the roller shutter. Check that the opening stops at the point
wanted. In the negative, adjust it using plastic wheel 3 according to the sign + or -.
7) After adjusting, replace the cover and fix the same with the screw.
1) Mount the clutch disk on the upper cover of the electric motor.
2) Use the screws 1 supplied to fix the electrobrake (plate, wound bobbin and sheet metal support) on the
upper cover.
3) Remove the cover of the limit switch 2 box.
4) Insert the two wires of the feeder into the clamps 1and 2 of the shutter motor
5) Place the limit switch box cover on and fit it by means of the special screw.
1) This instruction booklet is only addressed to qualified specialists.
2) Use low voltage to perform up and down movements of the shutter.
3) We recommend the use of original CAB accessories.
4) Use cables with a minimum section of 1.5 mm
5) Cables must not get in contact with metal parts in order to avoid short circuits.
6) All products manufactured by AUTOMATISMI CAB S.r.l. are guaranteed.
The warranty is limited exclusively to repair or substitution cost free of the pieces which will be acknowledged
by the company as faulty due to poor quality of materials or manufacture.
Any complaints will not, under any circumstances, give the Buyer the right to cancel or reduce the order, nor
will it oblige AUTOMATISMI CAB S.r.l. to pay compensation for damages of any kind.
The guarantee loses its validity if the goods, returned as faulty, have been tampered with, repaired or defects
arising from the influence of external agents, incorrect maintenance, overloading, normal wear and tear, er-
roneous choice of model, incorrect installation or any other factor not attributable to AUTOMATISMI CAB
S.r.l.
AUTOMATISMI CAB S.r.l. is only responsible for damages caused by any accidents resulting from faulty
products, required by Italian law.
The warranty requires that the system is in compliance with the regulations in force and the accessories
used are original AUTOMATISMI CAB S.r.l. In the event of defective accessories, indicate the serial number
of the motor.
10
Gearmotor installation (fig.1a-b)
Limit switch adjustment (fig.2)
Electrobrake assembly (fig.3)
Notes and guarantee
.
2
Publicidad
