Publicidad
Idiomas disponibles
Idiomas disponibles
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
HALF LOAD - If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and detergent.
Remember to halve the amount of detergent.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
LOADING THE RACKS
UPPER RACK
(loading example for
the upper rack)
Load delicate and light dishes:
glasses, cups, saucers, low
salad bowls.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS
POSSIBLE CAUSES
The dishwasher does
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
not fill the water.
The inlet hose is bent.
Display shows: H,
6 and On/Off LED is
The sieve in the water inlet hose is clogged;
blinking rapidly
it is necessary to clean it
Dishwasher finishes the
Drain hose positioned too low or siphoning
cycle prematurely. Display
into home sewage system.
shows: 15 and On/Off
LED is blinking rapidly
Air in water supply.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.bauknecht.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-
sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
2
LOWER RACK
(loading example for the lower rack)
For pots, lids, plates, salad bowls, cutlery
etc.. Large plates and lids should ideally
be placed at the sides to avoid interferen-
ces with the spray arm.
B
A
C
Please scan the QR code on your product in order to have more detailed information.
-
DELAY
The start of the program may be delayed for a period of time
between 1 and 12 hours.
The DELAY function cannot be set once a wash cycle has been started.
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
The basket is equipped with top grilles for improved cutlery
arrangement. The cutlery basket should be positioned only
at the front of the lower rack.
Knives and other utensils with sharp edges must be
placed in the cutlery basket with the points facing
downwards or they must be positioned horizontally in
the tip-up compartments on the upper rack.
More information in the Daily Reference Guide on website.
CLEANING THE SPRAY ARMS
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
Please scan the QR code on your product in order to have more detailed information.
SOLUTIONS
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwa-
sher and reboot.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check
for siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
CAPACITY: 14 standard place-settings
CUTLERY BASKET
The lower spray arm may
be removed by pulling it
upwards.
:
400011658681D
03/2023 ks - Xerox Fabriano
IEC 436
Publicidad
