Panasonic NI-W920A Instrucciones De Operación página 5

C A U T | O N To reduce the risk of personal injury and
damage to your iron:
@ Do not use water additives or substitute water such as scented water in the steam iron. They can
stain fabrics.
e If the Steam/Dry Selector is not at Dry position after using, remaining water will move into the
Soleplate and can result in burns when the iron is used next time.
@ Do not use the Steam or the Jet of Steam while the mains lead is unplugged, water will remain
inside the Soleplate and cause staining.
Do not use the Steam or the Jet of Steam while the Temperature Selector is set to "0".
O Most tap water can be used in this iron. If water is very hard, distilled or demineralized water should
be used. Do not use water processed through home water softening systems because this water
contains minerals that may be harmful to the iron. Do not use water additives or substitute water
such as linen or scented water in the steam iron. They can stain fabrics or damage the iron.
€ When adding water to the iron, please hold the iron firmly to avoid dropping, or it may result in injury.
e Do not set the Steam/Dry Selector to the steam position unless the iron is sufficiently hot to
produce steam, otherwise water will leak out through the vents instead.
@ Do not use the " Jet of Steam Button " until the Thermostat Operating Indicator Light turns off
after setting the Temperature Selector to * MAX ". Hot water may leak from the Soleplate and
burns may be resulted, and it may cause corrosion.
e If synthetics are being ironed on a higher temperature level than instructed, not only will the
fabric be ruined, but the Soleplate will often be covered with the melted remains of the synthetic
fabric.
READ THESE INSTRUCTIONS
For proper use of your iron, read the remaining safety cautions and operation instructions.
For your safety, please read the following text carefully (For UK only)
This appliance is supplied with a molded three pin mains plug for your safety and convenience.
A 13 ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13
ampere and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark e» or the BSI mark Ç on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local dealer.
If the fitted molded plug is unsuitable for the socket outlet in your home then the fuse should be
removed and the plug cut off and disposed of safely.
There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket.
How to replace the fuse Figure A Figure B
The location of the fuse differs according to the type
of AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
Open the fuse cover with a screwdriver and replace
the fuse and close or attach the fuse cover.
8
Fuse cover
(A)| COMPONENTS IDENTIFICATION
@ Steam/Dry Selector Handle
@ Spray Mist Button AD Thermostat Operating Indicator Light
@) Jet of Steam Button(Vertical Steam Button) (Temperature Select Indicator)
@ Water Fill Cover 42 Temperature Selector
(6) Spray Nozzle 13 Heel Rest
© Soleplate 44) Mains Lead
45) Plug (Plug type to comply with respective
countries or region requirement.)
| 48) Cup (MAX 310 mL)
(2 Maximum Water Level Indication
Water Tank(Water Window)
Self-Cleaning Button
HELPFUL IRONING TIPS
The Temperature Selector has words, dots and steam symbols. The dots are symbols for 3
temperature ranges:
e Low Temperature
ee Medium Temperature
eee High Temperature
Some fabrics are labeled with these dots as a guide for selecting the proper ironing temperature
setting.
Note: The Thermostat Operating Indicator Light goes on and off alternately to indicate the
changing temperature of Soleplate. If you turn the Temperature Selector from a high
temperature to a lower temperature, wait until the indicator light turns on before using
the iron.
©] HOW TO FILL WATER
1. Set the Steam/Dry Selector to the Dry position to avoid water leakage.
Open the Water Fill Cover, hold the iron as shown and fill the iron with water up to " MAX "
dot (about 310 mL). Use a cup for filling (see Note).
2. Check for the correct water fill level with the iron in the vertical position.
3. Close the Water Fill Cover, or water will splash from the Water Tank when ironing.
Note: Do not overfill the Water Tank. The steam will release through the vents when the iron
is positioned vertically.
(D| HOW TO USE AS A STEAM IRON
1. Fill the iron as described in " HOW TO FILL WATER `.
2. Position the iron vertically and be sure the Temperature Selector is set to " 0 ".
3. Plug the mains lead into the household mains socket.
4. Set the Temperature Selector to the steam zone ("<> " to " & "). The Thermostat Operating
Indicator Light goes on.
If the temperature of Soleplate is high, the light does not go on.
" «5 " zone: Low steam, for thin or delicate fabrics requiring a small amount of steam.
"$" zone: High steam, for fabrics requiring a lot of steam. (i.e. thick materials, items with
stubborn wrinkles).
5. Preheat the iron until the Indicator Light goes out, usually it takes about 1 minute.
The light will go on and off while ironing to indicate the temperature chosen by the Temperature
Selector is being maintained.
6. Hold the iron horizontally and set the Steam/Dry Selector to the steam position.
7. Whenever the iron is positioned vertically, the steaming action will stop.