Descargar Imprimir esta página

EINHELL GC-CH 1846 Li Manual De Instrucciones Original página 16

Ocultar thumbs Ver también para GC-CH 1846 Li:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 82
4. Technical data
Cutter rail length ..................................... 520 mm
Cutting length ......................................... 460 mm
Tooth spacing ........................................... 15 mm
Cuts/min ...................................................... 2200
Sound pressure level, L
Uncertainty K
: ............................................ 3 dB
pA
Sound power level, L
WA
K
uncertainty .......................................... 3.6 dB
WA
Interchangeable battery ......18 V d.c. / 2000 mAh
Sound power level guaranteed L
Vibration a
......................................... ≤ 2.5 m/s²
hv
K uncertainty ............................................1.5 m/s
Weight ........................................................2.0 kg
Battery charger
Mains voltage ....................200-250 V ~ 50-60 Hz
Output voltage/current .................. 20 V d. c. / 3 A
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Anl_GC_CH_1846_Li_SPK13.indb 16
Anl_GC_CH_1846_Li_SPK13.indb 16
GB
.................. 80,7 dB (A)
pA
...................... 88.7 dB (A)
........ 92 dB(A)
WA
2
- 16 -
Switch the appliance off when it is not in use.
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
5. Before starting the equipment
5.1 Installing the battery (Fig. 4)
Press the side pushlock buttons of the battery
pack as shown in Fig. 4 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 1, make sure that the
pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.2 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons (Fi-
gure 2/Item 9).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(5) into the mains socket outlet. The green
LED will then begin to flash.
3. Insert the battery pack (6) into the battery
charger (5).
4. In section "Charger indicator" you will find a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
27.09.2023 08:30:43
27.09.2023 08:30:43

Publicidad

loading

Este manual también es adecuado para:

Gc-ch 1846 li kit34.106.42: 34.106.83