Bojungle B725000 Instrucciones De Uso página 27

48: Crib lock function: Follow the steps to unlock the bed.;Press the unlock button with one hand, and use the other hand to lock
the bed. Pull the lever apart and pull it to the position shown in figure 48B. The crib can be locked by the opposite operation.
Warning: When using the rocking function of the rocker, the lock state of the bed must be released! Otherwise, the swing
function cannot be used!
Power supply instructions, this product host uses two power supply methods:
•
49: The first power supply method is: 5V~6V/0.8A DC power adapter for power supply: insert the DC plug of the
adapter into the power interface (A12 in Figure A-1), and then The AC plug is inserted into the AC socket of 100-240V
;
50/60Hz 0.3A Warning: Do not use adapters not supplied with this product to power the product! The input
voltage of the adapter is 100-240V/50/60Hz 0.3A, and the output voltage is 5-6V/0.8A! When using the adapter,
keep the adapter away from children!
50: The second power supply method is: 4 AA batteries, use a screwdriver to loosen the battery cover screws until the
•
cover can be taken out, take out the cover, / The negative polarity direction corresponds to insert the battery, then
close the cover, and tighten the screws. Use the same steps to remove the battery;
Warning: The screws of the battery cover must be locked, otherwise there will be liquid leakage, which will be a safety
risk! Batteries must be inserted with correct polarity! Do not install it in reverse, otherwise it will not be powered on! Non-
rechargeable batteries cannot be charged! Rechargeable batteries should only be charged under adult supervision!
Rechargeable batteries should be removed from the product before charging! Different types of batteries and old and new
batteries cannot be mixed! Depleted batteries should be removed from the product, disposed of immediately, and kept
away from children!
Control panel function introduction (image 51)
The power button connect the power supply, and press the ① button to control the switch.
Warning: Because the circuit board has a certain memory function, when the power is unplugged, the stored power
cannot be released immediately. At this time, if the power is plugged in immediately, the button may fail. If the button
fails, just press ① before plugging in the power. This problem can be solved by pressing 3~5 keys, this is a normal
phenomenon, please use it with confidence!
51: The swing gear. There are 5 swing gears to choose (from the first swing to the fifth swing, the swing gradually increases),
press the ② key to control the gear, and press the first light to turn on the first swing (minimum swing). Press the 2nd indicator
light for the 2nd gear, press the 3rd indicator light for the 3rd gear, press the 4th indicator light for the 4th gear, press the fifth
indicator. The fifth indicator light is 5-speed swing (maximum swing), and the indicator light goes out when the sixth light is
pressed. Repeat the above operation to cycle through the gear selection.
Warning: After each gear is selected, since the main board needs a certain time to calculate the swing data, it needs to wait
for about 10 seconds before the swing amplitude is normal. During this period, the push-pull method cannot be used to
assist the swing, otherwise it needs to wait again. The swing range is normal, this is a normal situation, please use it with
confidence!
The swing mode key is shown as (③ in Figure 51), and there are 7 swing modes to choose from. Press the ③ key to select the
swing mode.
Warning: Before pressing the ③ key to select the swing mode gear, you need to press the ② key (② in Figure 51) to select
the swing mode first, and then select the swing mode gear! Otherwise, the swing pattern described below cannot be
presented! But it can also be operated independently (the ③ key in Figure 51)!
The swing mode functions are introduced as follows (image 53-59):
• 53: 1st gear mode is the automatic cycle mode: press the ③ key until the first indicator light is on, it is the automatic
cycle mode, which sets 5 different swings. The modes are automatically cycled and swayed in every 16-seconds.
• 54: 2nd gear mode: Press the ③ key until the second indicator light is on, and the swing track is as shown in (Fig. 54).
55: 3rd gear mode: Press the ③ key until the third indicator light is on, and the swing track is as shown in (Fig. 55).
•
• 56: 4th gear mode: Press the ③ key until the fourth indicator light is on, and the swing track is as shown in (Fig. 56).
• 57: 5th gear mode: Press the ③ key until the fifth indicator light is on, and the swing track is as shown in (Fig. 57).
58: 6th gear mode: Press the ③ key until the sixth indicator light is on, and the rocking trajectory is as shown in (Fig.
•
58).