KNOVA KN MS-625A Manual página 2

TABLE OF CONTENTS
Table of contents ............................................................. 1
Technical specifications KN MS-625A ............................. 1
Introduction ...................................................................... 1
Safety rules ...................................................................... 1
Outline for KN MS-625A hollow chisel mortiser .............. 2
Receiving the mortiser ..................................................... 3
Installation ........................................................................ 3
Adjustments ..................................................................... 3
TECHNICAL SPECIFICATION KN MS-625A
Input power:
Output power:
Chisel sizes range:
Maximum chisel depth:
Maximum chisel stroke:
INTRODUCTION
This manual has been prepared for the owner and operators of Model KN MS-625A hollow chisel mortiser. Its purpose, aside
from proper machine operation, is to promote safety through the use of accepted correct operating and maintenance
procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain
maximum life and efficiency from your mortiser, and to aid in using the machine safely, read this manual thoroughly and follow
all instructions carefully.
SAFETY RULES
As with all power tools there is a certain amount of hazard
involved with the operation and use of the mortiser. Use the
tool with the respect and caution demanded where safety
precautions are concerned. This will considerably lessen the
possibility of personal injury. When normal safety precautions
are overlooked or completely ignored, personal injury to the
operator can result.
Know your tool. Read the owner's manual carefully. Learn
the tools applications and limitations, as well as the specific
potential hazards peculiar to it.
Keep guards in place and maintained in working order.
Ground all tools. If tool is equipped with three-prong plug,
it should be plugged into a three-hole electrical receptacle.
If an adapter is used to accommodate a two-prong receptacle,
the adapter plug must be attached to a known ground.
Never remove the third prong.
Remove adjusting keys and wrenches. Form habit of
checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
Keep work area clean. Cluttered areas and benches invite
accidents.
Avoid dangerous environment. Do not use power tools in
damp or wet locations, or expose them to rain. Keep work
area well lighted.
Keep children and visitors away. All children and visitors
should be kept a safe distance from work area.
Make workshop childproof - with padlocks, master switches,
or by removing starter keys.
Do not force tool. It will do the job better and be safer at
the rate for which it was designed.
Use proper tool. Do not force tool or attachment to do
a job for which it was not designed.
1,100 W.
1 HP., 120 V, 60 Hz.
1/4" - 1" (6.35 - 25.4 mm)
2-3/4", (70 mm)
8-1/4", (210 mm)
Operation .......................................................................
Maintenance ..................................................................
Wiring diagram ...............................................................
Parts list .........................................................................
Parts diagram .................................................................
Parts list for stand assembly ..........................................
Notes .............................................................................. 9
Drill chuck capacity:
Spindle speed:
Cross stroke:
Longitudinal stroke:
Vertical stroke:
Wear proper apparel. Do not wear loose clothing, gloves,
neckties, or jewelry that can get caught in moving parts.
Non-slip footwear is recommended. Wear protective hair
covering to contain long hair.
Use safety glasses. Also use face or dust mask if cutting
operation is dusty.
Secure work. Use clamps or a vise to hold work when
practical. It's safer than using your hand and frees both hands
to operate tool.
Do not overreach. Keep your proper footing and balance
at all times.
Maintain tools in top condition. Keep tools sharp and clean
for best and safest performance. Follow instructions for
lubricating and changing accessories.
Disconnect tools before servicing and when changing
accessories such as chisel and bit.
Use recommended accessories. Consult the owner's manual
for recommended accessories. The use of improper
accessories may cause hazards.
Avoid accidental starting. Make sure switch is in "OFF"
position before plugging in cord.
Never stand on tool. Serious injury could occur if the tool
is tipped or if the cutting tool is accidentally contacted.
Check damaged parts. Before further use of the tool, a guard
or other part that is damaged should be carefully checked to
ensure that it will operate properly and perform its intended
function - check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.
Never leave tool running attended. Turn power off. Do not
leave tool until it comes to a complete stop.
Drugs, alcohol, medication. Do not operate tool while under
the influence of drugs, alcohol, or any medication.
1
1/8" - 5/8", (3 - 16 mm)
1,750 RPM
5-1/2", (140 mm)
6-5/8", (168 mm)
5-1/2", (140 mm)
4
4
5
6
7
8