GE Profile 405 Manual Del Propietário página 8

About yourdryer features.
Color Logic
Selecl tile ( onect FABRIC CAREseuing. Mat(h
the particular color below tile words _fith tile
same color on the Cyde Dial.
Example: Drying a load of clothing labeled
permanent press.
El ( hoose tile FABRIC CAREseuing--for tllis
load it wouM be the EASYCARE MED.
HEAT(whi(h is a particular (olor).
['_ Tmn tile (ycle Dial to tile _uea that has
the same (olor as the FABRIC CAREsetting
you have _hosen-fi)r this load it wouM be
tile EASY CARE AUTOMATIC.
WRINKLE CARE
EXTENDED COOL AIR TUMBLE
Wrinkle Care
Use this option to minimize tile wrinkles
in clothes. It provides approximately 15
minutes of no-heat rambling after the
clothes are (hy.
This option can only be used with tile
COTTONS, EASY CARE, D ELICATES, and
ULTRACAREcycles.
If you _ue using the CYCLE
SIGNALand y{)uselect the WRINKLE CARE
option, a signal will sound at tile end of tile
(hTing time and sevetM times during tile
WRINKLE CARE _ycle. This will remind
you
that it is time to remove the (lothes.
If WRINKLE CAREis not ON,the (hyer will stop
on(e tile timer rea(hes tile WRINKLE CARE
mark on tile o_(le dial.
SIGNAL
ELECTRONIC TONE
(appearance may vary)
End of Cycle Signal
This signal _dll sound just beli)re tile end
of tile _):_le to remind you to rem_)ve tile
clothes. On some models, tile signal sound
level can be adjusted.
If you selected tile WRINKLECAREoption
tile signal will sound at tile end of tile
duing time and will sound several times
during the WRINKLE CAREcycle. This will
remind you that it is time to remove tile
clothes.
NOTE:
• Remove garments promptly at the sound
of the signal. Place clothes on hangers
so wrinkles won't set in.
• Use the END OF CYCLE SIGNAL especially
when drying fabrics like polyester knits
and permanent press. These fabrics should
be removed so wrinkles won't set in.
Dryness
Sensor Cycle
Dryness Sensor Cycle-on some models
This teatme is only activated in tile
COTTONS, E ASYCARE, D ELICATE& and
ULTRACARE cycles.
Tile DrynessSensor provides greater
&wing accuracy than standard machines,
resuhing in shorter d U times and better
clothes care. As the clothes tumble, they
touch a moisture sensor. The sensor will
stop the heating qcle its soon as the clothes
have reached the selected duness.
On some models, there is a Dryness
Sensor Cycleindicator
light. This light is
illuminated during automatic cycles.
When tile DrynessSensorleatme stops tile
heating cycle, the light will go out and the
cool down period will begin.
Note: Tile clothes
xdll be hot if they are
removed immediately after tile indicator
light goes out.
Drum Lamp
Before repladng tile light bulb, be sure to
unplug tile (hyer power cord or (fis(onnect
tile (hyer at tile household disuibution panel
by remox4ng tile fhse or switching off tile
drcuit breaker. Reach above duet opening
fiom inside tile dram. Remove tile bulb and
replace with the salne size bulb.
Automatic Cycle
Signal
Automatic Cycle Signal-on some models
At tile end of each {ycle there is
approximately 15 minutes of no-heat
rambling after tile laun(hy is (hy.
A reminder signal will sound periodically
during this time to remind you to remove tile
laund U.
8