Milwaukee M12 HAMMERVAC 2509-20 Manual Del Operador página 4

SYMBOLOGY
Volts
Direct Current
UL Listing for Canada and U.S.
C US
SPECIFICATIONS
Cat. No. ..................................................... 2509-20
Dust Box Cat. No .................................. 42-16-0580
Crevis Tool Cat. No ............................... 49-90-2325
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
Max Bit Diameter ........................................... 1-1/4"
Hammer Collar Sizes
Diameter
Ø 41-61 mm (1.6"-2.4")
Recommended Ambient
Operating Temperature ......................0°F to 125°F
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always remove the
battery pack before removing the dust box. Do
not use tool without dust box and HEPA filter
in place.
Installing/Removing the Dust Box
and HEPA Filter
To remove the dust box:
1. Turn OFF the tool.
2. Remove the battery pack.
3. Press the dust box latches. (1)
4. Pull the dust box away from the
HAMMERVAC™. (2)
5. Empty debris by holding away
from the user's face and tap-
ping dust box into a trash can,
pail, or other reasonable con-
tainer. For best cleaning
results, connect a
vacuum hose with dust
extraction adapter (Cat
No. 49-90-1959) to the
dust box port and suc-
tion out debris.
6. If necessary, pull the
HEPA filter away from
the dust box and tap
clean. Do not clean
with water or compressed air. After about 1500
holes or loss of suction, discard and replace HEPA
filter (Cat. No. 49-90-2306).
Circumference
129-192 mm (5.1"-7.5")
2
Dust box
port
HEPA
filter
To install the dust box:
1. Slide the dust box into the body of the
HAMMERVAC™.
2. The dust box latches should snap into place.
NOTE: Do not operate the HAMMERVAC™ without
the dust box and HEPA filter in place. Dust box cannot
be installed without HEPA filter.
CAUTION
dent on the filter. A dirty filter will reduce the air
flow and overall efficiency of the system. Do not
clean with water or compressed air. Remove from
dust box and tap clean.
Installing/Removing Nozzle Assembly
To install the nozzle assembly
supplied with the tool, or acces-
sory nozzles:
1. With the nozzle assembly
pointing straight up, line up the
lugs of the nozzle assembly
with the lugs on the front of the
HAMMERVAC™. The unlock
symbol on the nozzle as-
sembly will line up with the
depth gauge on the top of the
HAMMERVAC™.
2. Turn the nozzle assembly left
or right to lock into place. The
lock symbol
assembly will line up with the
depth gauge on the top of the
HAMMERVAC™.
3. To remove, reverse the proce-
dure.
Installing/Removing Nozzle
Replace the nozzle:
• After drilling about 1500 holes,
• When the bit brush shows signs
of wear,
• When suction is reduced,
• When dust escapes through the
bit brush during use
To replace the Standard (Cat.
N o . 1 4 - 5 2 - 0 1 0 5 a n d L a r g e
Cat. No. 14-52-0110) nozzles, ro-
tate the nozzle release lever up to
the open position and pull out nozzle from the lower
1
nozzle assembly (Cat. No. 42-20-0615) Slide the new
nozzle into the lower nozzle assembly and rotate the
nozzle release lever down to the closed position.
Attaching the HAMMERVAC™ to a Rotary
Hammer/Hammer Drill
The HAMMERVAC™ is provided with a clamping
collar assembly and one side handle grip.
1. Turn OFF, remove the battery pack from the
HAMMERVAC™, and disconnect power from
the tool.
2. Remove the tool side
hand le by fl i pp i ng
clamp lever upwards.
3. S l i d e
HAMMERVAC™ side
handle clamping col-
lar assembly over the
chuck and onto the
neck of the tool.
4. Attach the side handle
clamping collar assem-
4
Keep filter clean. Efficiency of the
HAMMERVAC™ is largely depen-
on the nozzle
Clamp
lever
t h e
Upper
Jaw
Lower
Jaw