Descargar Imprimir esta página

Kenmore ELITE HE3 110.4282 Serie Manual Del Propietario E Instrucciones De Instalación página 18

Lavadora automdtica de carga frontal

Publicidad

Idiomas disponibles

Idiomas disponibles

WASHER CARE
Cleaning
the exterior
Use a soft damp cloth or sponge to wipe up any spills,
Occasionally
wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products,
Cleaning
the interior
Use a soft damp cloth or sponge to occasionally
wipe the inner
door to remove any detergent residue. Use mild soap and water.
Do not use abrasive products.
Cleaning
the door seal
Use a soft damp cloth or sponge when necessary. Check the fold
of the seal periodically for any foreign objects.
Cleaning
the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
See "Using the Dispenser." Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments
and the separator).
3. Wash the parts under running water.
4. Replace the inserts and return the dispenser to the drawer.
Replace inlet hoses after five years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use
or vacation
care:
Operate your washer only when you are at home, If you will be on
vacation or not using your washer for an extended period of time,
you should:
Unplug washer or disconnect
power.
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize
washer:
1. Put I qt (1 L) of R.V.-type antifreeze in the drum.
2. Run washer on a DRAIN/SPIN cycle.
3. Unplug washer or disconnect
power.
4. Shut off both water faucets.
5. Disconnect
water inlet hoses from faucets and drain.
To use washer
again:
1. Flush water pipes.
2. Reconnect water inlet hoses to faucets.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
5. Run the washer through the NORMAL/CASUAL
cycle with
_/2the normal recommended
amount of HE detergent to clean
out antifreeze,
To transport
the washer:
1. If washer will be moved during freezing weather, put in 1 qt
(1 L) of R.V,-type antifreeze in the drum, Run washer on a
DRAIN/SPIN cycle.
2. Unplug the power cord,
3. Disconnect
the drain hose from the drain system and attach
to rear panel clips.
4. Shut off both water faucets.
5. Disconnect the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
6. IMPORTANT: Call Service. Do not reuse transport
bolts. Unit
must be transported
in the upright position. To prevent
suspension and structural damage, your machine must be
properly set up for relocation by a certified technician.
Reinstalling
the washer
1. Follow the "Installation
Instructions" to locate, level and
connect the washer.
2. Run the washer through the NORMAL!CASUAL
cycle with
_/2the normal recommended
amount of HE detergent to clean
the washer and remove the antifreeze, if used.
Slightly open door to provide ventilation.
18

Publicidad

loading

Este manual también es adecuado para:

Elite he3 110.4483 serieElite he3 110.4482 serie