Publicidad
Idiomas disponibles
Idiomas disponibles
o. Never place the tool down until the bit or ac-
cessory has come to a complete stop.
p. Do not grasp the tool or place your hands
too close to the spinning chuck or drill bit.
Your hand may be lacerated.
q. When installing a drill bit, insert the shank
of the bit well within the jaws of the chuck.
If the bit is not inserted deep enough, the grip
of the jaws over the bit is reduced and the
loss of control is increased.
r. Do not use dull or damaged bits and acces-
sories. Dull or damaged bits have a greater
tendency to bind in the workpiece.
s. When removing the bit from the tool avoid
contact with skin and use proper protective
gloves when grasping the bit or accessory.
Accessories may be hot after prolonged use.
t. Check to see that keys and adjusting
wrenches are removed from the drill before
switching the tool "ON". Keys or wrenches
can fly away at high velocity striking you or a
bystander.
u. Do not run the tool while carrying it at your
side. A spinning drill bit could become entan-
gled with clothing and injury may result.
v. If devices are provided for the connection
of dust collection and extraction systems,
empty the dust container before beginning
work, frequently during work, after comple-
tion of work, and before storing the tool. Be
extremely careful of dust disposal, materials
in fine particles form may be explosive.
w. Do not throw dust on an open fire. Combus-
tion from mixture of varnishes, lacquers, poly-
urethane, oil or water with dust particles can
occur if there is a static discharge, electric
spark, or excessive heat.
x. Do not use dust extraction for operations
where dust may include burning, smoking or
smoldering items like hot ashes or sparks.
Fire inside the vacuum tank or bag may occur.
Dust may smolder and set vacuum on fire long
after work is completed.
y. Do not use dust extraction with explosive
dusts, varnish, polyurethane coatings, clean-
160992A7BZ GBH18V-22 20230316.indd 5
Hammer Safety Warnings
z. Do not use dust extraction when working on
aa. Do not drill into metal with the dust extrac-
ab. Do not drill into wood with dust extraction
ac. Your tool is equipped with a dust canister,
ad. Note: Do not use the dust extraction sys-
2. Safety instructions when using
long drill bits with rotary hammers
a. Always start drilling at low speed and with
b. Apply pressure only in direct line with the
c. Never operate at higher speed than the max-
d. Use clamps or another practical way to se-
-5-
ers, or oil-based paints. Electric motors cre-
ate sparks which may ignite the dust or fumes.
metal. Swarf from drilling metal may be hot
and may spark which may melt plastic adap-
tors, vacuum hoses and may cause a fire in-
side the vacuum tank or bag.
tion system mounted. Hot metal chips can
self-ignite or ignite parts of the dust extrac-
tion system.
system mounted. Wood chips are typically
too large and will clog the dust channel.
empty it frequently, after completion of
drilling and before storing the tool. Be ex-
tremely careful of dust disposal, materials in
fine particle form may be explosive.
tem when chiselling, screwdriving or cut-
ting threads.
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if al-
lowed to rotate freely without contacting the
workpiece, resulting in personal injury.
bit and do not apply excessive pressure. Bits
can bend causing breakage or loss of control,
resulting in personal injury.
imum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to
rotate freely without contacting the work-
piece, resulting in personal injury.
cure and support the workpiece to a stable
platform. Holding the work by hand or against
your body leaves it unstable and may lead to
loss of control.
3/16/23 9:33 AM
Publicidad
