Dreame VTV41B Manual Del Usuario página 11

Use the trigger switch lock to free your
EN
fingers and avoid finger fatigue caused by
holding the switch.
Fig. D-2
Note:
• In this mode, the lock indicator will
illuminate steadily.
• Click the trigger switch lock again to quit
the Continuous Cleaning Mode.
Using Different Accessories
Multi-Surface Brush
- When using on baby play mats, carpets
or for vacuuming coffee beans, pop corn
and other pellets, turn on the switch on the
brush.
- When vacuuming on tiles, wooden floors
or other hard surfaces, turn off the switch.
Fig. E-3
Note:
• The multi-surface brush can be attached
directly to the vacuum.
• When the appliance starts, the lights in
front of the brush roller will automatically
turn on, which is convenient for use.
Motorized Mini-Brush
For vacuuming dirt, pet hair, and other
stubborn debris from sofas, bedding, and
other fabric surfaces.
Fig. E-4
Note: It is not recommended to vacuum on
fragile surfaces, such as silk.
Soft Roller Brush
Suitable for cleaning hard floors such as
marbles and tiles.
Fig. E-5
Note: The soft roller brush can be attached
directly to the vacuum.
Wide Combination Tool
For vacuuming curtains, keyboards, ceilings,
sofas, vehicle interiors, coffee tables, etc.
Fig. E-6
14
Flexible Combination Tool
Bendable and retractable brush-nozzle,
more flexible to vacuum in narrow gaps.
Fig. E-7
Wall Mount
The vacuum cleaner can be placed on the
wall mount when it is not in use.
Note:
• Do not put the vacuum cleaner alone on
the wall mount.
• Place it on the wall mount after
connecting it with the extension rod and
the multi-surface brush.
Fig. E-8
Note:
• If any rotating part becomes stuck, the
vacuum may shut off automatically.
Remove any trapped foreign objects, then
resume use.
• When the motor becomes overheated,
the vacuum will automatically shut off.
Wait until the battery temperature returns
to normal, then resume use.
Care & Maintenance
Tips:
1. Always use genuine parts to keep your
warranty from being void.
2. If the filter or nozzle becomes clogged,
the vacuum will stop working shortly
after being turned on. Clear the tube to
restore functionality.
3. If the vacuum is not used for an extended
period, fully charge it, unplug its charger,
and store it in a cool, low-humidity
environment away from direct sunlight.
To avoid over-discharging the battery,
recharge the vacuum at least once every
three months.
Cleaning the Vacuum
Wipe the vacuum with a soft dry cloth.
Cleaning the Dust Cup, Pre-
Filter, and Cyclone Assembly
The vacuum's cleaning ability will be
reduced if the dust cup is filled to the
"MAX" mark. To regain performance, empty
the dust cup in a timely manner. Before
emptying the dust cup, make sure the
vacuum is disconnected from the power,
and do not press its power button.
1. Press the dust cup bottom cover release
button, then empty the contents.
Fig. F-1
2. Push the dust cup release switch in the
direction indicated by the arrow, then gently
remove the dust cup from the vacuum.
Fig. F-2
3. Remove the pre-filter first, then lift the
handle of the cyclone assembly and turn it
counterclockwise until it stops, then pull to
lift out the cyclone assembly.
Fig. F-3
4. Wipe the dust cup with a soft wet cloth.
Pay attention to wringing out the cloth
before using.
Fig. F-4
To avoid the risk of electric shock, do not
rinse the dust cup with water.
5. Rinse the cyclone assembly and pre-filter
until they are clean. After washing, air dry
for at least 24 hours .
Fig. F-5
Note:
• It is recommended to clean the dust cup
once every month.
• It is recommended to clean the pre-filter at
least once every 3 months and the cyclone
system at least once every 6 months.
Installing the Dust Cup, Pre-
Filter, and Cyclone Assembly
1. Insert the cyclone assembly vertically into
the dust cup, and make sure that the handle
of the cyclone assembly line up with the
slot on the left side of the dust cup. Turn the
handle clockwise until it locks, then flip the
handle down.
2. Place the pre-filter with its front side
facing up into the cyclone assembly.
Fig. F-6
3. Slightly tilt the dust cup so the slot aligns
with the clip on the vacuum. Then gently
push the dust cup until it clicks into place.
Fig. F-7
Cleaning the Filter
It is recommended to clean the filter once
every 4 to 6 months.
Fig. F-8
1. Remove the dust cup as shown in the
figure.
2. Remove the filter from the vacuum by
pulling it down in the direction shown in the
figure.
Fig. F-9
3. Clean the filter with clean water. Make
sure you rotate the filter 360° to thoroughly
and remove all dust caught in the filter.
Lightly tap the filter several times to remove
any excess dirt.
Fig.F-10
4. Allow the filter to air dry for 24 hours.
Fig. F-11
Note：
• Only use clean water to wash the filter. Do
not use detergent.
• Do not attempt to clean the filter with a
brush or finger.
Installing the filter
1. Insert the filter into the vacuum and
gently press down, as illustrated.2. Reinstall
the dust cup.
Fig. F-12
2. Reinstall the dust cup.
Fig. F-13
EN
15