Publicidad
Idiomas disponibles
Idiomas disponibles
CARDIN ELETTRONICA spa
Via Raffaello, 36- 31020 San Vendemiano (TV) Italy
Tel:
Fax:
email (Italy):
email (Europe):
Http:
DIGITAL RADIO CONTROLS WITH ROLLING CODES S449
REMARKS
These instructions are aimed at professionally qualified "installers of electrical equipment" and must respect the local
standards and regulations in force. The use and installation of these appliances must rigorously respect the indications
supplied by the manufacturer and the safety standards and regulations in force.
Attention! Only for EU customers - WEEE marking. This symbol indicates that once the products
life-span has expired it must be disposed of separately from other rubbish. The user is therefore
obliged to either take the product to a suitable differential collection site for electronic and electrical
goods or to send it back to the manufacturer if the intention is to replace it with a new equivalent
version of the same product. Suitable differential collection, environmental friendly treatment and
disposal contributes to avoiding negative effects on the ambient and consequently health as well
as favouring the recycling of materials. Illicitly disposing of this product by the owner is punishable
by law and will be dealt with according to the laws and standards of the individual member nation.
Description
The S449 Radio control system in "FM" consists of one or more transmitters and one or more receivers which can be
combined to meet the specific needs of the system. The generated code is memorised in the receiver via radio. The receiver
is able to memorise up to 300 different codes.
Important: The transmitted code changes for each command (rolling code). If disturbance interrupts the transmission,
the receiver will wait for a different code, the relay can then only be activated by first releasing and then pressing the
transmitter channel button again.
Use
The S449 radio control allows the remote activation of electrical and electronic appliances with its best use in the following
areas: automatic opening systems, alarm systems, and in all systems which require remote control activation (without
wires) using secret codes.
Transmitter versions
TRQ449100
Miniaturised transmitters
TRQ449200
Miniaturised transmitters
TRQ449300
Miniaturised transmitters
TRQ449400
Miniaturised transmitters
TRQ44940M
Wall mounted transmitter
Receiver versions
RQM449200
Mini receiver
RSQ449200
Slot-in receiver card
RCQ449100
Outdoor receiver
Memory module (M1)
The module is furnished with a non volatile EEPROM type memory and contains the transmitter codes and allows you
to memorise up to 300 codes (300 channel buttons). The programmed codes are maintained in this module even in the
absence of power.
Receiver antenna installation
'Range' is intended to mean the working distance, measured in free space, between the receiver and the transmitter with the
antenna installed. The range is therefore closely linked to the technical characteristics of the system (power and sensibility)
and varies according to the characteristics of the site in which the system is located. It therefore follows that to obtain the
best results from the radio control the receiver and antenna installation sites should be carefully chosen. It is good practise
to position the receiver away from computer systems, alarm systems and other possible sources of disturbance.
A bad choice of positioning could compromise the performance of the receiver.
Antenna
The installation of the antenna is fundamental, connected to the receiver it represents the reception point for the radio
control. When installing the antenna the following points should be observed. A tuned antenna using a coaxial cable RG58
(impedance 50Ω) with a maximum length of 15 m. must be installed. The antenna should be positioned out of doors in the
highest possible point, visible and away from metal structures.
Transmitters
The transmitter is pre-coded and is fitted with an integrated circuit which is programmed in the factory with a unique
identification number. All the code parameters are contained in this integrated circuit (external memory modules are not
required) thus making code management more reliable and the system more secure. The transmitter has an automatic shut
down mechanism which cuts in after at least 25 seconds of continuous use (this limits battery consumption).
• This time can vary from transmitter to transmitter.
Receivers
Warning! The receivers must only be powered by a safety power pack. The use of non safety power packs could
provoke damage to the system.
Outdoor receivers IP55 (fig. 6)
- The outdoor receiver card (CS1120A) is fitted with an 14-way terminal board and has the following electrical connections:
- 12V ac/dc between binding posts 1-2 - 24V ac/dc between binding posts 1-3.
The outdoor receiver is fitted using "fast-fitting" brackets. The bracket should be fixed to the wall using two rawlplugs
(check that it is in square). After connecting the wiring the case should be slid onto the bracket therefore fixing it to the
wall. If any repair work is necessary the case can be easily extracted by pushing upwards the action of which will separate
it from the bracket.
Interchangeable channel modules
In the receivers the channel functions are printed on the circuit board. The interchangeable channel modules can only
have the following configuration:
- from 1 to 4 impulsive relay strips MCC4491R0
Slot-in receiver cards (fig. 7)
Warning! The receiver cards must be sufficiently insulated from the parts of the host device which are powered by the mains.
- The receiver card (printed circuit CS1134) is inserted directly into an appliance which is designed to receive it and has
the following electrical connections: 24V ac/dc between binding posts 3-4
The receiver cards are fitted with two relays the outputs of which are marked CH1 (N.O. contact) and CH2 (N.O./N.C. contact).
The relays CH1 and CH2 can be activated by selecting the functions A-B-C-D and made to correspond with the transmitter
channels CHA-CHB-CHC-CHD by setting the jumpers "J1" situated on the circuit board (see fig. 7).
Mini receivers IP20 (fig. 8)
- The mini receiver (printed circuit CS1134) is housed in an indoor container and is fitted with an 8-way terminal board
with the following electrical connections:
- 12V ac/dc between binding posts 7-8 - 24V ac/dc between binding posts 6-8.
The receiver cards are fitted with two relays the outputs of which are marked CH1 (N.O. contact) and CH2 (N.O./N.C. contact).
The relays CH1 and CH2 can be activated by selecting the functions A-B-C-D and made to correspond with the transmitter
channels CHA-CHB-CHC-CHD by setting the jumpers "J1" situated on the circuit board (see fig.8).
+39/0438.404011-401818
+39/0438.401831
Sales.office.it@cardin.it
Sales.office@cardin.it
www.cardin.it
1 Button
2 Buttons
3 Buttons
4 Buttons
4 Buttons
2 Channels
2 Channels
4 Channels
SERIAL NUMBER
ZVL407.04
The S449 series conforms to the essential requirements of the directive 99/05/
CE and the technical reference standards have been applied.
Frequency validity: 433.92 MHz for all
Status led "L1" on the receiver
Flashing rapidly: cancelling a single user
Flashing slowly
memorising a single user
Continuously lit: memory full
Functions
Attention! Before memorising the transmitters for the first time remember to cancel the entire memory content.
Memorising a channel (fig. 5a,6,7,8)
1. Keep button "P1" MEMO pressed down and the led "L1" will start to flash slowly
2. Press the channel on the transmitter which is to be memorised
3. Keep button "P1" MEMO pressed down until led "L1" starts to flash again
4. Release the button and the LED continues to flash
5. Press the channel on the transmitter which is to be memorised again (same transmitter, same channel. If the channel
or the transmitter is different you will not be able to memorise the channel.
6. End of the memory procedure. LED "L1" will remain lit for 2 seconds meaning that the channel has been correctly
memorised.
• It is not possible to memorise a user code that is already in memory: In this case when the transmitter is activated
(point 2) the led will stop flashing. The program will only work again when button "P1" MEMO has been released.
• If the transmitter is not activated a second time within fifteen seconds the program will automatically leave the memory
mode without memorising a new user code.
• If a new user code is activated the first time and a different channel (with an already memorised user code) is activated
the second time, the program will automatically leave the memory mode (because the two codes do not correspond)
and the channel present in the second transmission will be activated.
Cancelling a channel (fig. 5a, 6, 7, 8 )
1. Keep button "P2" DELETE pressed down and the led "L1" will start to flash rapidly
2. Press the channel on the transmitter which is to be cancelled
3. Led "L1" will remain lit for 2 seconds meaning that the channel has been cancelled.
Note: If the user which is to be cancelled is not found in the memory, the led will stop flashing. The program will only
work again when button "P2" has been released. If the button is released before a channel is activated the program
will automatically leave the memorising or cancelling mode.
Cancelling the entire user memory (fig. 6, 7, 8)
1. Keep buttons (P1+P2) pressed down simultaneously for more than 4 seconds
2. Led "L1" will remain lit for the period of time required for the program to cancel all the codes (about 8 seconds)
3. Led "L1" will turn off meaning that the cancellation procedure has been carried out.
Note: It is only possible to switch from memorising mode to cancelling mode if you haven't already entered the second
part of the memorising procedure (point 4 onwards). Once this part of the procedure has been reached the entire
procedure will have to be completed. If you do not wish to memorise a code which you have already transmitted wait
for 15 seconds, the led will switch off and the code won't be memorised. When the receiver's memory is almost full the
user search function can take up to 1 second to complete.
Memorising a channel (fig. 5b)
•
Memorisation can be activated by radio (without opening the receiver container) if jumper "J3" has been inserted
(fig. 6, 7, 8).
1. Make sure that the jumper "J3" has been inserted in receiver.
2. Using a transmitter, in which at least one channel button "A,B,C or D" has already been memorised in the receiver,
press the button "MR" as shown in figure "5b".
Note: all the receivers within range when the channel button is pressed (and which have at least one of the transmitter
channel buttons memorised) will activate their signal buzzer "B1" (fig. 6,7,8).
3. Press one of the channel buttons on the transmitter. The receivers which do not contain that channel code will
sound a five-second long "beep" and will then disactivate. The receivers which contain the channel code will sound
a one-second long "beep" and will enter the programming mode.
4. Press one of the channel buttons on the transmitter which you wish to memorise; the receiver will sound 2 "beeps"
of half a second each after which the receiver will be ready to receive another code.
5. To leave the programming mode wait for 5 seconds without pressing any buttons. The receiver will sound a five-
second long "beep" and will then exit the programming mode.
•
When the memory is entirely occupied the buzzer will sound 10 rapid "beeps" and will automatically leave the
"programming via radio" mode.
Led "L1" will remain lit on the receiver. The same signal is given each time you try to enter "programming via radio"
when the memory is full.
TECHNICAL SPECIFICATIONS
RECEIVER
- reception frequency .......................................................................................................................................433,92 MHz
- local oscillation frequency ............................................................................................................................423,22 MHz
- local oscillation tolerance ....................................................................................................±30PPM from -20 to +75 °C
- sensitivity (finely tuned signal) .................................................................................................................-110dBm 0,7µV
- selectivity ............................................................................................................................................................. ±30 kHz
- modulation .................................................................................................................................................................. FSK
- modulation with ∆F ...............................................................................................................................................≤20 kHz
- antenna impedance in input...................................................................................................................................... 50 Ω
- receiver power supply ................................................................................................................................12/24V ac/dc
- maximum power consumption at rest/with 1 relay activated ..........................................................................20/40 mA
- maximum commutable power at the relay with resistive load:
load ac/dc ........................................................................................................................................................60VA/24W
maximum voltage ............................................................................................................................................ 30V ac/dc
- relay activation delay time ........................................................................................................................... 80 to 100 ms
- operating temperature range ......................................................................................................................-20°...+75 °C
TRANSMITTERS
- carrier frequency ............................................................................................................................................433,92 MHz
- carrier frequency tolerance ................................................................................................................................. ±30 kHz
- apparent radiated power .......................................................................................................-10...-7dBm (100-200 µW)
- apparent power harmonic products .....................................................................................................<-54dBm (<4nW)
- modulation ........................................................................................................................................................... FM/FSK
- modulated with ∆F ...............................................................................................................................................≤20 kHz
- power supply (lithium battery) ........................................................................................................................2 x CR2032
- power consumption ............................................................................................................................................... 35 mA
- operating temperature range ........................................................................................................................ -10...+55°C
- relative humidity .......................................................................................................................................................<95%
- type of encoding .............................................................................................................................................rolling code
- total number of possible code combinations (66 bit) ..................................................................................................2
- number of channels .........................................................................................................................................................4
- automatic shut down ................................................................................................................ after at least 25 seconds
SERIES
MODEL
S449
FM
21-11-2001
countries
DATE
66
Publicidad
