Publicidad
Idiomas disponibles
Idiomas disponibles
STEP 2
Connect the Track and Upright to the Cross Bar
Parts Required:
4a. Short Track
4b. Long Track
5
5. Ramp
7. Upright
7
11. Socket Wrench
12. Allen Key
13. Washers x 4
14. Nuts x 4
15. Long Bolts M6*15 mm x 4
Overlap the Short Track (4a) with the Long Track
(4b) and align the holes to make one Track (4).
Then insert two Long Bolts (15) through those
holes. Place a Washer (13) followed by a Nut (14)
on the protruding ends of the Long Bolts (15).
Secure the Nuts (14) to the Long Bolts (15) by
using the Socket Wrench (11) and Allen Key (12).
Place the Short Track (4a) section of the track
(4) on top of the L-Piece (2) and align the first
hole on the Short Track (4a), the one closest
to the Cross Bar (1), with the first hole on the
L-Piece (2). Insert a Long Bolt (15) from the
underside of the L-Piece (2) through the first
hole in the Short Track (4a) section. Then place
a Washer (13) and Nut (14) on the protruding
section of the Long Bolt (15) and tighten the
L-Piece (2) to the Short Track (4a) section using
the Socket Wrench (11) and Allen Key (12).
Place the Upright (7) in front of the "L-Piece (2)
and align the bottom (first) hole on the
Upright (7) with the middle hole on the L-Piece
(2). Insert a Long Bolt (15) from the outside of
the L-Piece (2) through the middle hole in the
L-Piece (2) and through the bottom hole of the
Upright (7). Then place a Washer (13) and Nut (14)
on the protruding section of the Long Bolt (15)
and tighten the L-Piece (2) to the Upright (7)
using the Socket Wrench (11) and Allen Key (12).
4a
4b
13
14
15
11
4b
14
13
2
4a
5
4b
15
7
!
14
13
4
STEP 3
Connect the Diamond Bracket to the Track and Upright
Parts Required:
6. Diamond Bracket
11. Socket Wrench
12. Allen Key
13. Washers x 2
14. Nuts x 2
15. Long Bolts M6*15 mm x 2
12
Place the Diamond Bracket (6) on top of the
Short Track (4a) and in front of the Upright (7)
so that the hole in the Diamond Bracket (6)
is aligned with the second hole in the Short
Track (4a), and the other hole in the Diamond
4a
Bracket (6) is aligned with the end hole in the
L-Piece (2) as well as the second hole from the
bottom in the Upright (7).
Connect the Diamond Bracket (6) to the
Short Track (4a) section and the L-Piece (2)
by placing a Long Bolt (15) through the end
hole in the L-Piece (2), through the hole in
the Short Track (4a) section, and through the
one hole in the Diamond Bracket (6). Place a
Washer (13) and Nut (14) on the protruding
Long Bolt (15) and tighten the Diamond
Bracket (6) to the Short Track (4a) section and
the L-Piece (2) using the Socket Wrench (11)
and Allen Key (12).
Connect the Diamond Bracket (6) to the
Upright (7) by placing a Long Bolt (15)
through the end hole in the L-Piece (2),
through the hole in the Upright (7), and
through the other hole in the Diamond
Bracket (6). Place a Washer (13) and
Nut (14) on the protruding Long Bolt (15)
and tighten the Diamond Bracket (6) to the
Upright (7) and the L-Piece (2) using the
Socket Wrench (11) and Allen Key (12).
15
13
6
14
15
7
6
7
14
14
13
13
15
5
11
12
15
Publicidad
