Publicidad
Idiomas disponibles
Idiomas disponibles
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
Press the Anynet + button.
.
Press the ▲ or ▼ button to select "Receiver", then press the ENTER button.
.
Press the ◄ or ► button to select to "On", then press the ENTER button.
Now you can listen to sound through the receiver.
.
Press the EXIT button to exit.
When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack.
When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home
theater receiver. When the source is a digital component such as a DVD and is connected to the TV
via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.
When using the WISELINK feature, sound may not output properly through the receiver.
When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred language)
menus.
Troubleshooting for Anynet +
Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on the
screen.
The Anynet + device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output
through the receiver.
Solution
Check if the device is an Anynet + device. The Anynet + system supports Anynet +
■
devices only.
■
Connect only one receiver (home theater).
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
■
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■
■
Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work at a certain condition. (Searching channels, Operating
■
WISELINK)
■
When connecting or removing the HDMI 1.3 cable, please make sure to search
devices again or restart your TV.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and check if the Anynet +
■
(HDMI-CEC) is set to On in the Anynet + Setup menu.
■
Press the TV button on the TV remote control to switch to TV. Then press the
Anynet + button to show the Anynet+ menu and select a menu you want.
■
Select View TV in Anynet+ menu.
■
Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
■
Press any of CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.
(Note that the channel button operates only when a tuner-embedded Anynet + device
is not connected.)
You cannot use the remote control when you are configuring Anynet + or switching to a
■
view mode.
Use the remote control when the Anynet + setting or switching to view mode is
■
complete.
Check whether or not the device supports Anynet + functions.
■
■
Check whether or not the HDMI 1.3 cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■
Search Anynet + devices again.
■
You can connect an Anynet + device using the HDMI 1.3 cable only. Some HDMI
■
cables may not support Anynet + functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English -
Air
Recevier:
On
Connect Recorder
Setup
Move
Enter
Exit
Publicidad
