Publicidad
original wrapper.
Transportation without the original wrapper
may result in damage on the device and the
company shall not take any responsibilities.
Do not drop the product or subject it to physical
shock. Keep the device away from magnetic
interface.
Power Supply
Please purchase the charger by yourself. Input
voltage should meet the Limited Power Source
(12 VDC) according to the IEC62368 standard.
Please refer to technical specifications for detailed
information.
Make sure the plug is properly connected to the
power socket.
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards
caused by overload.
DO NOT touch the bare metal contacts of the
inlets after the circuit breaker is turned off.
Electricity still exists.
+ identifies the positive terminal(s) of equipment
which is used with, or generates direct current. -
identifies the negative terminal(s) of equipment
which is used with, or generates direct current.
Ensure correct wiring of the terminals for
connection to an AC mains supply.
Battery
Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according
to the instructions.
The built-in battery cannot be dismantled.
Please contact the manufacture for repair if
necessary.
For long-term storage of the battery, make sure
it is fully charged every half year to ensure the
battery quality. Otherwise, damage may occur.
This equipment is not suitable for use in
locations where children are likely to be present.
Improper replacement of the battery with an
incorrect type may defeat a safeguard (for
example, in the case of some lithium battery
types).
DO NOT dispose of the battery into fire or a hot
oven, or mechanically crush or cut the battery,
which may result in an explosion.
DO NOT leave the battery in an extremely high
temperature surrounding environment, which
may result in an explosion or the leakage of
flammable liquid or gas.
DO NOT subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas.
Installation
Never place the equipment in an unstable
location. The equipment may fall, causing serious
personal injury or death.
This equipment is for use only with
corresponding brackets. Use with other (carts,
stands, or carriers) may result in instability causing
injury.
System Security
You acknowledge that the nature of Internet
provides for inherent security risks, and our
company shall not take any responsibilities for
abnormal operation, privacy leakage or other
damages resulting from cyber attack, hacker
attack, however, our company will provide timely
technical support if required.
Please enforce the protection for the personal
information and the data security as the device
may be confronted with the network security
problems when it is connected to the Internet.
Please contact us when the device might exist
network security risks.
Please understand that you have the
responsibility to configure all the passwords and
other security settings about the device, and keep
your user name and password.
Maintenance
If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance.
A few device components (e.g., electrolytic
capacitor) require regular replacement. The
average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Wipe the device gently with a clean cloth and a
small quantity of ethanol, if necessary.
If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the device may be impaired.
To reduce the risk of fire, replace only with the
same type and rating of fuse.
The serial port of the equipment is used for
debugging only.
Disconnect the power source during servicing.
Using Environment
Make sure the running environment meets the
requirement of the device. The operating
temperature shall be -20 °C to 50 °C (-4 °F to
122 °F), and the operating humidity shall be 5% to
95%, no condensing.
DO NOT expose the device to high
electromagnetic radiation or dusty environments.
DO NOT aim the lens at the sun or any other
bright light.
The equipment shall not be exposed to dripping
or splashing and that no objects filled with liquids,
such as vases, shall be placed on the equipment.
No naked flame sources, such as lighted candles,
should be placed on the equipment.
Provide a surge suppressor at the inlet opening
of the equipment under special conditions such as
the mountain top, iron tower, and forest.
Burned fingers when handling the parts with
symbol
. Wait one-half hour after switching
off before handling the parts.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Manufacture Address
No.555 Qianmo Road, Binjiang District, Hangzhou
310052, China
Hangzhou Hikvision Digital Technology Co.,Ltd.
COMPLIANCE NOTICE: The thermal series products
might be subject to export controls in various
countries or regions, including without limitation,
8
Publicidad
