Descargar Imprimir esta página

Palram Feria 3x3 Instrucciones De Armado página 2

Ocultar thumbs Ver también para Feria 3x3:

Publicidad

IMPORTANT
Please read
these instructions carefully before you start to assemble this patio
cover. Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe place
for future
reference.
>>
Care
and Safety advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check the list
of
contents.
For
safety purposes we
strongly recommend that the product will
be
assembled
by at least
two
people.
Some parts have metal edges. Please be careful when
handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to
assemble the
product
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if
you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you
are
prone to dizzy
spells.
When using
a
stepladder
or
power tools, ensure that you follow the manufacturer's
safety advice.
Do
not climb
or stand on
the roof.
Heavy articles should
not
be
leaned against the poles.
Do
not
hang or
lay on
the profiles.
Please
consult your
local
authorities if
any
permits
are
required to construct the
product.
Keep
roof
and
gutter
clean
of
snow,
dirt
& leaves.
Heavy
amounts of snow
on
roof
can
damage the
product
making
it unsafe
to stand
below
or nearby.
This
product
was
designed and produced to
be
a
patio
cover
only.
Some versions
of
this product
are
painted.
If color
was scratched
during assembly it
can be
fixed
with
the following tints:
White
-
RAL
9016
Gray
-
RAL
7012
»
Cleaning instructions
When
your product
needs cleaning,
use
a
mild detergent solution and
rinse
with
cold
clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panel.
»
Before
starting assembly
This
product must
be
assembled on
a
solid
base (such
as
concrete).
Choose
your
site
carefully before beginning
assembly.
Site
surface (mainly
below
poles) needs
to
be level.
During assembly
use
a
soft platform below the parts to avoid scratches and
damages.
»
Product dimensions adjusting
Product dimensions
can be
adjusted to your specific
needs.
1.The
wall-mounting
profile (top-back)
can be
adjusted
from
285
to
305 cm
(122.2"to
120")
above ground.
The
adjusting
is
done when measuring and drilling
(step
7).
2. Poles
distance from the wall
can be
adjusted from
226
to
286 cm (89"
to
112.5").
The
adjusting
is
done after
assembly and before
anchoring
(step
22)
by
sliding
poles and
profile
1041
at channels
of roof
profiles.
3.
Poles
distance from the
side
edges can be
adjusted from
0
to
54 cm (0"
to
21.3").
The
adjusting
is
done after
assembly and before
anchoring
(step
22)
by
sliding
poles and
connectors
937 at channel
of
profile
1041.
Note:
Wall
mounting
and
distance
from the wall determine
the roof angle and the total
depth of the product
(distance
of gutter from the
wall).
Higher wall
mounting
and shorter distance between
wall
and poles increase
the roof
angle and shorten the total
depth. Tighten
all screws
when
completing assembly
285-305cm
112.2"
-120"
IEEE
a
am
0
-
54cm
0"-
21.3"
0
-
54cm
0
'-
21.3"
13°
17°
- - -

Publicidad

loading