Publicidad
Idiomas disponibles
Idiomas disponibles
English
Initial Setup
Essential Setup
1. Place the unit on a flat and level surface. The selected location should be stable and free from vibration.
2. Install the turntable lid to the hinges.
3. Remove the tie-wrap that is holding the tonearm.
4. Remove all packing material from underneath the turntable hub.
5. Install the turntable platter and drive belt accordingly.
6. Slide Tonearm Counterweight onto tonearm with the numbers facing the front of the turntable, and twist it lightly onto
the rear shaft of the tonearm
7. Adjust the counterweight to set proper stylus pressure.
8. Place the slip mat on top of the turntable platter.
9. Connect AC adaptor to the Power Jack of the unit.
Note: Do not plug the AC power adaptor to power outlet before all the assembly is completed. Before turning the power on, make sure
again all the connection settings are correct. Always turn off the power when connecting or disconnecting.
Turntable Platter and Belt Setup
1. Put the drive belt around the Turntable Hub, and then use the provided drive belt assembly tool to help pull the belt
to fit around the slot of motor pulley.
2. Place the turntable platter through the turntable spindle.
Tonearm Counterweight Adjustment for Stylus Pressure
1. Remove the stylus protector from the cartridge and avoid touching the stylus tip during the adjustment.
2. Release the tonearm Hold Down Clip, gently hold the tonearm and move it away from the Tonearm Rest. At this point,
the tone arm is unbalanced and free to swing.
3. Lift up the Tonearm from its rest and gently hold it. The tone arm is unbalanced at this point.
4. Carefully rotate the Counterweight towards the front of the turntable until the tonearm is horizontally balanced and
hovers freely just above the platter without the stylus touching the platter surface.
5. Return the tonearm to the Tonearm Rest and lock the Hold Down Clip.
6. While holding the counterweight steady without any rotation, rotate carefully only the Downforce Scale Dial until the "0"
on the scale lines up with the centerline marked along the top of the tonearm.
7. Rotate the counterweight including the downforce scale dial counter-clockwise (as seen from the front of the turntable)
to adjust the pressure to the stylus manufacturer recommendations.
Note:
-
Each mark on the scale represents 0.05 g (gram).
-
The recommended pressure for the factory-installed cartridge is 3.5 g.
-
One full turn of the counterweight will provide a pressure 2.0g. In order to reach a stylus pressure that is greater than 2.0 g keep
rotating the counterweight forward.
Stereo System Connection
RCA Jacks
• The RCA Jacks of this unit are shared as both the Phono output jacks and the Line output jacks. They are determined
by the Phono/Line Switch.
• When used as a line output, the jacks output analog line-level signals and could be connected directly with a pair of
active speakers or the appropriate input of your stereo system. When used as a Phono output, they should be
connected to the phono pre-amp or the phono input of the stereo system.
• The Red plug connects with the Right channel and the White plug connects with the Left channel.
Note:
− If the Phono/Line switch is set at LINE position but RCA jacks connected to the stereo system's phono input, the sound might be
distorted due to input overload and could damage your stereo system.
− If the Phono/Line switch is set at PHONO position but RCA jack connected to the stereo system's line input, the volume will be very
low due to lacking signal pre-amplification.
− RCA Jack is not designed to be connected directly to the passive/unpowered speakers and if it does, the volume will be very low.
Spring clip speaker terminals
The spring clip speaker terminals deliver amplified, speaker-level signals as output and should be connected with the
passive speakers.
5
Publicidad
