Publicidad
Idiomas disponibles
Idiomas disponibles
UK
NL
DE
FR
Technical Data:
Type LED: 20 W COB
Brightness: 2000 ~ 400 Lumen (5 steps)
Battery: 7.3 V 4.0 Ah Li-Ion
IP rating: IPX4
IK rating: IK07
Charging time: 3.5 hours
Run time: 1.5-10 hours
Working temperature: -20 ~ 50°C
Beam distance: 50 m
Wireless signal range: 12 m
Product dimensions: 212x139x65 mm
Technical data optional charger (SIN-100.1070-2):
Voltage: AC 100 V ~ 240 V
Frequency: 50/60 Hz
Charger output voltage: 8.4V 1.5A
Power connection:
Use the lamp within places prescribed and governed by current regulations on workplaces and electrical systems. Check that the
plugfitted on the cable is suitable for the work environment, if it is not, it must be replaced by a qualified electrician.
Main features:
• Long life LEDs (life span 100.000 hours)
• Wide beam distribution lens
• Lamp use is not affected by cold temperatures
Instructions for use:
• Charge the battery for at least 3.5 hours before first use
• To charge the lamp: connect and then plug into a wall socket.
Please re-charge in good time.
• The battery level indicator
progressively 3 blinking blue LEDs.
• The battery level indicator on the lamp will show 1 red LED and 3 blue LEDs when charging is complete
• The work light is controlled by switch
LED (1600 Lumen), 3x for LED (1200 Lumen), 4x for LED (800 Lumen, 5x for LED (400 Lumen) and 6x to turn the unit off.
• Memory function: After 6 seconds in one of the above settings, the lamp will turn off by pressing the switch
the same setting will be active
• Speaker: Press the
switch
LED will be on. When connection fails, the pilot lamp will blink again. After 10 minutes of no operation it will disconnect and turn off
automatically.
• Do not leave the battery in a fully discharged condition. Recharge the flashlight at least once every 30 days. Always fully charge the
battery to extend the battery lifetime.
Accessories and spare parts:
8.4V 1.5A charger with cable
Use only accessories and spare parts approved by the manufacturer.
Caution:
• Avoid looking directly into the beam
• Do not use the lamp near open fire
• Switch off the lamp when not in use
• Only use this lamp for the purpose it is designed to, all modifications are strictly prohibited
• Should any cable be damaged, it must be immediately replaced with one of the same type
• When plugging the charger into a suitable mains supply, always check that the device is in good condition, and does not appear
damaged as this may impair safety
Warranty/Service:
• 12 months from the date of the purchase – Proof of purchase is required to make any warranty claim
• The warranty does not apply in case of damage to the device due to negligent / improper use or accidental damage
2
ES
Lumen Laser class I
Protection class III
EAN: 8717775515180
Colour temperature LED: 6500 K
Weight: 1057 g
Hydrocarbon and UV resistant
on the lamp show 1 red blinking LED when charging is required. While charging it shows 1 red LED and
5
and press 3 seconds to turn on. Press the ON/OFF switch 1x for LED (2000 Lumen), 2x for
1
. The blue LED
will blink until it connects to the electronic device succesfully, then the blue pilot
2
6
2
8
• Made with high-quality materials for optimal use and durability
• Robust, shock resistant housing
• Magnetic base 4 X 45N
• 180° swivel base
5
7
3
4
On/off switch
1
switch
2
Output and input
3
180° swivel stand with magnets
1
4
Battery level indicator
5
Charging port 8,4 DC
6
Control panel
7
Brightness settings
8
. By turning it on again
1
6
Publicidad
