Antar AT52324 Manual De Instrucciones página 4

ENG
GENERAL WARNING
Do not use the product before reading and understanding this manual. If you do not understand any warnings, cautions or instructions, please contact your healthcare professional or
retailer to avoid damaging the product.
CONTRAINDICATIONS
Physical or mental limitations (e.g. visual impairment) that prevent the safe handling of the product.
PURPOSE OF THE PRODUCT
The wheelchair is intended for the transport of persons with disabilities and persons with mobility difficulties. The product is intended for use by one person
TARGET PATIENT GROUP
Persons suffering from diseases, dysfunctions or injuries for the treatment/rehabilitation or compensation of which this device is intended (see section on intended use of the device in
these instructions). The device can be purchased by the user independently or on the recommendation of a doctor, therapist or other specialist. Whether you purchase the device
yourself or on the recommendation of a doctor/therapist/other specialist, you must take into account the available sizes/necessary functions/sizes/variants of the device, the indications
and contraindications for use, as well as the information provided by the manufacturer.
TECHNICAL SPECIFICATIONS
Frame: aluminium
Dimensions L x W x H: 101 x 63 x 88,5 cm
Folded dimensions: 74 x 28 x 68 cm
Seat width: 46 cm
Seat depth: 40 cm
Backrest height: 42 cm
Armrest height: 20 cm
Height from the ground to the footrest: 18,5- 21 CM (2 steps of adjustment)
Seat height: 47 cm
Net weight: 10,7 kg
Gross weight: 12,4 kg
Maximum payload: 100 kg
Rear cast wheels: 20''
PVC front wheels: 6''
FEATURES OF THE PUSHCHAIR
- safety belt
- additional rear pocket
- calf stabiliser strap
- foldable backrest
- quick release rear wheels
This symbol indicates the user's maximum weight
REMARKS
1. Remember to apply the brake even after a short stop. It is important to get into the habit of applying the brakes.
2. The wheelchair cannot brake suddenly, therefore you should not accelerate excessively while driving.
3. When making a sharp turn, slow down to avoid tipping over.
4. Before moving the wheelchair, make sure that the patient is keeping his feet on the footrest.
5. Before use, check that all elements are properly assembled.
6. Make sure that the brake is on when getting in and out of the wheelchair.
7. When getting off the wheelchair, do not stand on the footrest as the wheelchair will tilt forwards.
8. Do not put the wheelchair near any source of fire.
9. There may be a risk of tipping over if the product is not used properly. Please follow the boarding / dismounting / moving instructions.
10. During use and handling of the product, as well as during its assembly and adjustment of mechanisms, there may be a risk of entrapment and / or pinching of body parts of the user /
accompanying person in openings / gaps between the elements. These steps should be performed with extreme caution. After completing the adjustment, stabilize the position by
tightening the nuts / bolts carefully. 11. It is forbidden to use the product other than in accordance with its intended purpose
SERVICE
FOLDING OUT A WHEELCHAIR WITH A FOLDING BACK
1. grasp the handle and lift it as indicated by the arrow to unfold the backrest.
2. while lifting the handle, press on the armrest.
3. press on the sides of the seat until the seat is fully unfolded.
4. lower the footrests down, fit the calf support belt.
UL_AT52324_AT52306
TECHNICAL SPECIFICATIONS AT52306
Frame: aluminium
Dimensions l.w: 106 x 62 x 92 cm
Dimensions when folded: 79.5 x 31 x 74 cm
Seat width: 46 cm
Seat depth: 40 cm
Height from ground to seat: 53cm
Height of backrest: 40cm
Height of armrest: 23cm
Height from the ground to the footrest: 19 - 21.5cm ( 2 degrees of adjustment)
Seat height: 51.5cm
Net weight: 12.4 kg
Gross weight: 14.3 kg
Maximum payload: 120 kg
Rear cast wheels: 23''
Front PVC wheels: 8''
Wheelchair equipped with anti-tip wheels
WARNING
When there is a characteristic clicking sound, this
means that the backrest frame is fully
extended,When there is a characteristic clicking
sound, this means that the backrest frame is fully
extended.