Publicidad
ENGLISH
Schartec roller-shutter remote control RH15
Frequency: 433.92 MHz Rolling-Code
Transmitting power: 10 mW
Channels: 15
Battery: CR2450 3V Lithium button cell
Working temperature: -20°C to +50°C
Article number: ST701011
Model number: DC2702
• Keep remotes out of reach of children.
• Remote controls may only be operated by persons who are familiar with the system and have been instructed in their function.
• Use the remote control only when you are in sight of the roller-shutter.
• Coding in remote controls must always be carried out within the vicinity of the operator. Use only original parts.
• Protect remotes from rain, snow, sunlight or dust, otherwise the function of the transmitter may be impaired
• To change the battery, use a tool such as a SIM card pin, mini screwdriver, needle, etc and press the small button in lower middle of the backside of the remote while sliding the cover down.
Program the remote control to a roller shutter/awning motor or radio receiver:
1. Slide the cover off the back of the remote.
2. Switch on the voltage of the roller shutter/awning motor or receiver.
3. Within 5 seconds of turning on the power, the motor will beep 3 times, press the P2 button on the remote once (it will beep and the motor will move up and down briefly); then press the P2 button again (after the brief move-
ment), it will beep again and the motor will move up and down briefly.
4. Immediately afterwards, press the Up button, the signal tone sounds 3 times and the motor moves up and down briefly. The remote control is now taught-in.
5. To change the buttons direction, repeat the procedure, but instead of pressing the Up button, press the Down button. Now the Up and Down buttons are reversed.
Set number of channels used
Press P1- and P1+ 1x
simultaneously
Display shows C
Programming additional remote controls
1. Press the P2 button once on the remote control that has already been taught-in (a signal tone sounds and the motor moves up and down briefly).
2. Then press the P2 button again (after the short movement), a signal tone sounds again and the motor moves up and down briefly.
3. Within 3 seconds, press the P2 button on the new remote control once; the beep sounds 3 times and the motor moves up and down briefly. The new remote control is now taught-in.
4. The new remote control has now taken over the coding from the already taught-in remote control. You can program up to ten remote controls per motor/receiver. When you teach in the eleventh remote, the first one is
deleted.
For "older" versions of the Schartec roller shutter motor, the back-and-forth movement of the motor when teaching the remote controls is omitted, but the process is exactly the same!
Schartec hereby declares that the remote control RH15 complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.schartec.de
As a dealer for the distribution of electronic, battery-operated devices, we are obliged by law to inform our customers about the following: Electrical and electronic devices, as well as batteries, must not be disposed of as house-
FRANÇAIS
Télécommande de volet roulant Schartec RH15
Fréquence: 433,92 MHz Rolling-Code
Puissance d'émission: 10 mW
Chaînes: 15
Batterie: CR2450 3V Pile bouton au lithium
Température de travail: -20°C à +50°C
Numéro d'article: ST701011
Numéro de modèle: DC2702
• Gardez les télécommandes hors de portée des enfants.
• Les télécommandes ne doivent être utilisées que par des personnes qui connaissent bien le système et qui ont été instruites de leur fonction.
• N'utilisez la télécommande que lorsque vous êtes en vue du volet roulant.
• Le codage des télécommandes doit toujours être effectué à proximité de l'opérateur. N'utilisez que des pièces d'origine.
• Protégez les télécommandes de la pluie, de la neige, du soleil ou de la poussière, sinon le fonctionnement de l'émetteur peut être altéré.
• Pour changer la pile, utilisez un outil tel qu'une broche pour carte SIM, un mini-tournevis, une aiguille, etc. et appuyez sur le petit bouton situé en bas au milieu de la face arrière de la télécommande tout en faisant glisser le
couvercle vers le bas.
Programmer la télécommande sur un moteur de volet roulant/store ou un récepteur radio:
1. Faites glisser le couvercle à l'arrière de la télécommande.
2. Mettez la tension du moteur ou du récepteur du volet roulant/store.
3. Dans les 5 secondes qui suivent la mise sous tension, le moteur émet 3 bips, appuyez une fois sur la touche P2 de la télécommande (un bip retentit et le moteur monte et descend brièvement) ; appuyez ensuite à nouveau sur la
touche P2 (après le bref mouvement), un nouveau bip retentit et le moteur monte et descend brièvement.
Press and hold P1- and
Press P1- or P1+ to
P1+ simultaneously
select the desired
(approx. 5 sec.)
amount of channels
Display shows 15
Looking for the video? Scan the QR code on page 1!
Simplified EU Declaration of Conformity (CE)
Information about battery regulation
hold or residual waste, but must be taken to appropriate battery acceptance and collection points.
The complete version of the battery law can be found here:
http://www.gesetze-im-internet.de/bundesrecht/battg/gesamt.pdf
a trademark of bau-shop-24 GmbH
Fritz-Müller-Strasse 115
73730 Esslingen
WEEE Reg. Nr.: DE90317979
BattG Reg. Nr.: DE50302356
Then confirm with stop
NOTE:
SCHARTEC
Germany
2
V. 231005
Display shows o
Done!
Publicidad
