Levenhuk Ermenrich NetGeeks NP10 Guia Del Usuario página 3

Ermenrich NetGeeks NP10 Cable & PoE Tester
EN
Please carefully read the safety instructions and the user manual before using this product. Keep away from children. Use the device
only as specified in the user manual.
The kit includes: transmitter, remote unit, user manual, and warranty.
Install batteries
Open the battery compartment cover and insert the battery according to the correct polarity marks. Close the cover.
Getting started
To turn on the transmitter, shift the three-position switch (1) to the middle position (ON)
To turn off the transmitter, shift the three-position switch (1) to upper position (OFF).
To turn the transmitter on and have its LED indicators blink slowly, slide the three-position switch (1) to the lower position (S).
Wire mapping
This function is used to check if the wires within the cable are connected correctly.
To test a network cable, plug one end of the cable into the RJ45 port (6) on the transmitter and the other end into the RJ45 port (9) on the
remote unit.
The results are shown with the corresponding LEDs (8). Possible outcomes are shown below:
Normal: The LEDs on the transmitter and on the remote unit will
blink green one by one.
Transmitter: 1-2-3-4-5-6-7-8-G
Remote unit: 1-2-3-4-5-6-7-8-G
Open: If pin 2 is open, the corresponding LEDs on the transmitter
and on the remote unit will not glow.
Transmitter: 1-x-3-4-5-6-7-8-G
Remote unit: 1-x-3-4-5-6-7-8-G
If less then two wires are connected, all the LEDs remain off.
Transmitter: х-x-х-х-х-х-х-х-х
Remote unit: х-x-х-х-х-х-х-х-х
To test a telephone cable, plug one end of the cable into the RJ11 port (7) on the transmitter and the other end into the RJ11 port (10) on the
remote unit. Possible outcomes are shown below:
Normal: The LEDs on the transmitter and on the remote unit will
blink green one by one (LEDs 1, 2, 3, 4, 5 for RJ11 cable test or LEDs
1, 2, 3, 4, 5, 6 for RJ12 cable test).
RJ11:
Transmitter: 1-2-3-4-5-х-x-x-x
Remote unit:1-2-3-4-5-х-x-x-x
RJ12:
Transmitter: 1-2-3-4-5-6-x-x-x
Remote unit:1-2-3-4-5-6-x-x-x
Open: If pin 2 is open, the corresponding LEDs on the transmitter
and on the remote unit will not glow.
RJ11:
Transmitter: 1-x-3-4-5-х-х-х-х
Remote unit: 1-x-3-4-5-х-х-х-х
RJ12:
Transmitter: 1-x-3-4-5-6-х-х-х
Remote unit:1-x-3-4-5-6-х-х-х
If less then two wires are connected, all the LEDs remain off.
Transmitter: х-x-х-х-х-х-х-х-х
Remote unit: х-x-х-х-х-х-х-х-х
Short: If pins 2 and 5 are short-circuited, the corresponding LED on
the transmitter will glow normally, but the corresponding LEDs on
the remote unit will not glow.
Transmitter: 1-2-3-4-5-6-7-8-G
Remote unit: 1-x-3-4-5-6-7-8-G
Cross: If pins 2 and 5 are cross-connected, the corresponding LEDs
on the transmitter and on the remote unit will blink in the same
manner.
Transmitter: 1-2-3-4-5-6-7-8-G
Remote unit: 1-5-3-4-2-6-7-8-G
Short: If pins 2 and 5 are short-circuited, the corresponding LED on
the transmitter will glow normally, but the corresponding LEDs on
the remote unit will not glow.
RJ11:
Transmitter: 1-2-3-4-5-х-x-x-x
Remote unit:1-x-3-4-x-х-x-x-x
RJ12:
Transmitter: 1-2-3-4-5-6-x-x-x
Remote unit:1-x-3-4-x-6-x-x-x
Cross: If pins 2 and 5 are cross-connected, the corresponding LEDs
on the transmitter and on the remote unit will blink in the same
manner.
RJ11:
Transmitter: 1-2-3-4-5-x-x-x-x
Remote unit: 1-5-3-4-2-х-x-x-x
RJ12:
Transmitter: 1-2-3-4-5-6-x-x-x
Remote unit: 1-5-3-4-2-6-x-x-x
3