Palram Martinique 4300 Instrucciones De Montaje página 3

1
L
IMPORTANT
Please read
these instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep these
instructions
in
a safe
place
for future
reference.
»
Care &
Safety Advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the contents
list.
For
safety purposes we strongly recommend the product to
be
assembled by
at least
two people.
Some parts have metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to assemble the
Gazebo
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them away from children's
reach.
Keep
children away from the assembly
area.
Do
not attempt to assemble the Gazebo if
you are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
When using
a
stepladder or power tools,
make sure
that you
are
following the
manufacturer's safety advice.
Do
not climb or stand on the roof.
Heavy articles should not
be
leaned against the poles.
Keep roof and gutters clear of
snow,
dirt
& leaves.
Heavy snow load on
roof
can
damage the
Gazebo,
making it unsafe to stand
below
or nearby.
This
product
was designed to be used mainly
as
a
Gazebo.
If the profiles' color
was scratched
during
assembly, it can be fixed.
»
Cleaning Instructions
In
order to
clean
the
Gazebo, use
a
mild detergent solution and rinse with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or other special detergents to clean
the
panels.
»Tools
&
Equipment
TO01(Supplied)
6,
Attention
Please make sure you install
the
panels
with the
UV
protected side
out
(marked with
"THIS
SIDE
OUT") and peel the film strip covering the
panels.
C---)
Please
tighten
all screws
when completing assembly.
Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete this stage
in
order for your warranty to
be
valid.
»
During Assembly
During assembly
use
a
soft surface below the parts to avoid scratches and
damages.
When encountering the information
icon, please refer to the
relevant assembly step for additional comments and
assistance.
Step 6b: Carefully
spread silicone along the cross-section
of the profile
and
immediately attach the profiles together.
It
is
recommended to wipe the extra
residue silicone.
Step 7+12:
It
is
recommended to
use
a
carton or
other soft material under the
lowered corner
in
order to avoid scratches and peeling of
paint.
*This note also refers to
steps 9,10,12
Step 10: Optional
-
if you wish to add curtains
/
mosquito netting
Please
thread the plastic clips through the
rail
in
each profile.
(Curtains
/
mosquito netting
are
not supplied).
Add clips according to the specific
quantity of curtain
rings.
Steps 12a+14a:
Please
note that screws insertion should
be
done from the
outside.
Steps 13+15:
Please note
that
screws
insertion should
be done from the
bottom
up.
Afterwards
please use
the tool
TO01.
Step 16b:
Please
add silicone on the inner
area
of part #8327
as
illustrated.
Step 22a:
Please
drill holes
in
the panels to
be
located precisely parallel to the
holes
in
profiles #7663.
Step
23:
Please
level the profile's legs and adapt
screws
and plugs to your specific
ground type.