Parkside Performance PWSAP 20-Li E6 Traduccion Del Manual De Instrucciones Originale página 32

GB MT
Technical data
Cordless Angle
Grinder ............... PWSAP 20-Li E6
Motor­voltage ............................. 20 V
Idling­speed­(n) .................... 10000 min
Cutting / roughing / grinding discs /brushes
Outside diameter
Grinding wheels /
Cut-off­wheels/
Disc brushes ............ max. Ø 125 mm
Bore hole ............................ 22.23 mm
Thickness
Grinding wheels .............. max. 6 mm
Cut-off­wheels ...............Max.­1.2­mm
Disc brushes .................... max. 5 mm
Cut-off­wheel
designs .....................diamond-studded,­
................bonded, reinforced, segmented
Spindle thread ............................. M14
Thread­length .............................. 11 mm
Sound­pressure­level­
(L ) ........................ 87.1 dB; K
pA
Sound­power­level­(L
measured .............. 95.1 dB; K
Vibration­level­(a )
h
Device­handle .. 3.44 m/s
Handle ........... 3.79 m/s
Temperature­(device­+­battery) . max.­50 °C
Charging process ...................4­-­40 °C
Operation .......................... -20­-­50 °C
Storage .................................0­-­45 °C
For use with smart batteries
(Smart PAPS 204 A1/Smart PAPS 208 A1)
Operating frequency/
Frequency band .... 2400­-­2483.5 MHz
Max.­transmission­power .......≤­20­dBm
Vibrations­levels­are­the­maximum­values­
generated by the cutting discs supplied.
The­actual­vibration­values­may­vary­de-
pending on the used accessories.
The­vibration­values­are­still­affected­by­
the handling for the user's.
32
= 3 dB
pA
)
WA
= 3 dB
WA
; K= 1.5 m/s
2
; K= 1.5 m/s
2
Cutting disc ................... WA60 T BF
Idling speed n
Disc­speed­v
0
Outer diameter ................... Ø 125 mm
Bore hole ........................ Ø 22.23 mm
-1
Thickness ................................ 1.2 mm
*
The cutting disc must withstand a rotational
speed of 80 m/s.
The­specified­total­vibration­value­and­the­
stated­noise­emission­value­have­been­
measured according to a standardised test
method and can be used to compare one
power tool with another.
The­specified­total­vibration­value­and­the­
stated­specified­noise­emission­value­can­
also­be­used­for­a­provisional­assessment­of­
the load.
Warning: The­vibration­and­noise­
emissions­may­deviate­from­the­
specified­values­during­actual­use­of­the­
power tool, depending on how the power
tool is being used and, in particular, what
kind of material is being worked on.
Safety measures for the protection of
2
the operator are to be determined that
2
are based on an estimate of the actual
vibration­load­under­the­real­operating­
conditions (for this, all parts of the opera-
ting cycle are to be taken into account, for
example, times in which the electric tool is
turned off, and those during which it is tur-
ned­on­but­running­without­a­load).
Charging time
The­device­is­part­of­the­(Parkside)­X 20 V­
TEAM­series­and­can­be­operated­with­bat-
teries­of­the­(Parkside)­X 20 V­TEAM­series.­
Batteries­of­the­(Parkside)­X 20 V­TEAM­
series may only be charged using chargers
of­the­(Parkside)­X 20 V­TEAM­series.
..................12200 min
max
............................ 80 m/s*
­(included)
-1