Publicidad
Idiomas disponibles
Idiomas disponibles
location of installation
Install your Dompel product in a level place with no grooves or splices, preventing
rocking and vibration. The location must be airy and it must not allow straight sun-
light and it must be away from sources of heat (stoves, ovens, etc.) and flammable
products. Do not install your product outdoors.
cleaning and maintenance
Do not use metal spatulas, brushes and cleaning agents such as alcohol, acetone, kerosene, gasoline, bleach, thinner,
solvents, varsol, vinegar or other chemicals or abrasives such as sand paper or steel brushes.
To easily clean it, use a solution of warm water with a neutral soap and then wipe dry carefully. If chemical products reach the
upholstery, clean as soon as possible, preventing the products from staining or drying the fabric. The plastic parts cannot be
washed with boiling water. Chromed metal components can be cleaned with a soft, dry flannel, and silicone-based automotive
wax can be used to increase gloss and durability, in this case perform the task following the wax manufacturer's instructions.
Perform periodic cleaning, accumulated dust affects the beauty of the product making it difficult to clean the product.
INSTALLATION AND ASSEMBLY
Remove all volumes from inside the package and follow these steps:
1
Join the seat structure (C) to the base support tubes (B).
Fit them manually using tube adapters pre-attached to the
base support tubes.
3
Remove the screws (M5 x 20) (F) pre-fixed on the base
support tubes (B) using Phillps wrench
5
Fasten the 02 screws (M5 x 20) (F) joining the seat
structure (C) to the base/basin set (A) using a Phillps
wrench. Access can be via the bottom or rear opening of
the base of the wash basin.
7
Inlet plastic faucet assembly: Assemble the faucet
set (E) and shower (E) in the basin (A), remove the
attached handle and the finishing of the threaded
faucet. After fitting the faucet on the bottom of the
basin and screw the finishing on the faucet on the top
of the basin giving the necessary tightening. Refit the
handle manually. Screw the shower on the connector.
Faucet
Head
Finishing
Faucet
9
Install the hoses (E) connecting to the faucet (E) in the options according to
the images and according to the need.
Installation with heater
Heater
eater
holder
upport
screws
Water faucet
hose to the
heater (DOES
NOTI NCLUDE)
Water faucet
hose to the
heater (DOES
NOTI NCLUDE)
NOT INCLUDE)
heater
Shower
attachment
hose to
heater
Shower
Shower
Connector
Faucet installation two entrances
Hot water
faucet hose
for shower
p
Cold water
faucet
hose for
shower
ENGLISH
2
During the assembly of item 01, observe the perfect fit of
the tube adapters (B), aligning the pins to the tube holes
according to the image detail:
4
Fit the seat structure (C) to the base/basin set (A), aligning
the tubes in the guides and holes in the base of the
washin unit.
6
Assemble the basin accessories according to the version
and type of installation required. Connect the faucet,
hoses and shower set (E) to the wash basin (A) according
to items 7, 8 and 9.
8
Two entrance faucet assembly - metal mixer faucet:
Assemble the faucet (E) and shower (E) in the
basin (A), remove the metal clamp and the hose
connector from the single handle faucet and fit the
upper part of the basin. Then, mount the metal
clamp and thread the hose connector securing the
single handle. When assembling the hose, make
sure that the smaller sealing washer is correctly
fitted to the hose connection. Thread the shower on
the connector.
Installation without heater
Water faucet
hose to the
shower
Water
faucet
hose to
the
shower
Water faucet
hose to the
water inlet
security
Avoid accidents. After
unpacking the product,
keep all the pack material
out of children's reach.
Two
Entrances
Faucet
Matal
Clamp
Hose
Connector
Shower
Hose
connector
Seal
Washer
10
Fit the plastic drain (D) to
the basin (A).
Shower
Publicidad
