Publicidad
Idiomas disponibles
Idiomas disponibles
E N
T E M PE R AT U R E
Press
to adjust the temperature.
•
Digital display shows the temperature setting 23
with 14 settings cycle from "OFF", "16
•
The TEMP will increase by 1
°C up to 28
•
By pressing the TEMP for 3
s, the digital display can show between °C
and °F.
TI M E R
Press the button
to switch between the OFF settings and 0.5 hours
to 9 hours.
M O O D LI G H T
Press the button
to switch between 14 effects, including the Off setting.
R E S E T TI N G T H E T H E R M A L C U T O U T
The appliance is fitted with an Electronic Safety Control (E.S.). This is a
safety device, which switches off the fire if, for any reason, the appliance over-
heats, e.g. when covered. If the heater stops operating while the flame effect
continues working normally, this indicates that the E.S. Control is in operation.
The E.S. Control can only be re -set after the appliance has cooled down,
and the appliance has been reset. Re -setting of the E.S. Control proceeds is
as follows:
1.
Switch off the appliance (Manual On
approximately 10 – 15 minutes.
2.
Remove any obstruction to the fan heater outlet or fan blades etc.
Make sure that the power supply is disconnected with the plug socket
outlet while doing this.
3.
Switch on the appliance and the E.S. Control will be re -set.
4.
Ensure that the appliance is functioning correctly. If the E.S. Control
doesn' t operates again, the appliance should be checked by a
competent electrician.
26
°C (default setting),
°C" to "28
°C".
°C when pressed each time.
/
Off switch) and leave it off for
E N
M AINTE N A NC E
WA R N I N G! Before any maintenance or cleaning of the ex terior of the
fireplace, the unit should be disconnected from the power supply until it
is cool off.
C H A N G I N G T H E R E M OT E C O N T RO L BAT T E R I E S
•
W h e n th e ba t te r ies a re fu ll y c ha r g e d , this sy m b o l is dis p laye d
•
W h e n th e ba t te r ies a re half full , this sy m b o l is dis p laye d
•
W h e n th e ba t te r ies a re e m p t y a n d n e e d to b e re p lac e d i m m e dia te l y,
this ba t te r y sy m b o l is dis p laye d
•
Ba t te r y re p lac e m e n t is re c o m m e n d e d af te r o n e yea r. T h e ba t te r ies a re
1.5 V alkali n e A A A ba t te r ies.
•
D is p ose of yo u r o l d ba t te r ies a t a su i ta b l e re c yc li n g fac ili t y.
M A I N T E N A N C E O F M OTO RS
The motors used on the fan and flame effect are pre -lubricated for ex tended
bearing life and require no fur ther lubrication. However, periodic cleaning
vacuuming of the fan
/
heater unit is recommended.
C L E A N I N G T H E FI R E PL AC E
You can clean the ex terior of the fireplace with a soft, damp, lint-free cloth.
Do not use cleaning or polishing products. To remove fingerprints or other
marks on the front glass panel, use a soft, damp, lint-free cloth with a good
quality household glass cleaner. The front glass panel should always be
completely dried with a clean, lint-free cloth or paper towel.
WA R N I N G! Abrasive cleaners should not be used on the glass panel.
Liquids should not be sprayed directly onto any surface of the unit.
/
27
Publicidad
