Bosch GBH 5-40 D Professional Instrucciones De Servicio página 15

► Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362). If the plug is not suitable for your
socket outlets, it should be cut off and an appropriate plug
fitted in its place by an authorised customer service agent.
The replacement plug should have the same fuse rating as
the original plug. The severed plug must be disposed of to
avoid a possible shock hazard and should never be inserted
into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Symbols
The following symbols can be important for the operation of
your power tool. Please memorise the symbols and their
meanings. The correct interpretation of the symbols helps
Symbol Meaning
you operate the power tool better and more secure.
To change the tool bit pull back the locking
sleeve.
Symbol Meaning
To change the tool bit pull back the locking
sleeve.
Product Description and
Specifications
Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury.
Intended Use
The machine is intended for hammer drilling in concrete,
brick and stone as well as for chiselling.
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
3 Mode selector switch
4 On/Off switch
5 Handle (insulated gripping surface)
6 Thumbwheel for speed preselection/impact frequency
preselection
7 Auxiliary handle (insulated gripping surface)
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
F 000 622 413 | 08.2015
Manual GBH 5-40 D - Professional.indd 15
Technical Data
Rotary Hammer
Article number
Rotary Hammer
Rated power input
Article number
Speed
Rated power input
Impact rate
Speed
Impact energy per stroke
according to EPTA-Procedure
Impact rate
05/2009
Impact energy per stroke
Chisel positions
according to EPTA-Procedure
05/2009
Tool holder
Chisel positions
Lubrication
Tool holder
Max. drilling dia.
Lubrication
– Concrete (with twist drill)
– Concrete
Max. drilling dia.
(with break-through drill bit)
– Concrete (with twist drill)
– Brickwork (with core bit)
– Concrete
Weight according to
(with break-through drill bit)
EPTA-Procedure 01/2003
– Brickwork (with core bit)
Protection class
Weight according to
The values given are valid for a nominal voltage [U] of 230 V. For differ-
EPTA-Procedure 01/2003
ent voltages and models for specific countries, these values can vary.
Protection class
Assembly
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
► Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle
► Operate your machine only with the auxiliary handle 7.
The auxiliary handle 7 can be set to any position for a secure
and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 7 in
counterclockwise direction and swivel the auxiliary
handle 7 to the desired position. Then retighten the
bottom part of the auxiliary handle 7 by turning in
clockwise direction.
Changing the Tool
With the SDS-max tool holder, simpler and easier tool
changing is possible without additional aids. The dust
protection cap 1 largely prevents the entry of drilling dust
into the tool holder during operation. When inserting the
tool, take care that the dust protection cap 1 is not damaged.
► A damaged dust protection cap should be changed
immediately. We recommend having this carried out
by an after-sales service.
Inserting (see figure A)
– Clean and lightly grease the shank end of the tool.
– Push back the locking sleeve 2 and insert the tool in a
twisting manner into the tool holder. Release the locking
sleeve 2 again in order to lock the tool.
– Check the latching by pulling the tool.
15
English |
GBH 5-40 D
3 611 B69 0..
GBH 5-40 D
W 1100
-1 3 611 B69 0..
min 170 – 340
-1 W 1100
min 1500 –2900
-1
min 170 – 340
-1
min 1500 –2900
J 8.5
12
J 8.5
SDS-max
12
Central permanent
lubrication
SDS-max
Central permanent
mm 40
lubrication
mm 55
mm 40
mm 90
mm 55
kg 6.8
mm 90
/II
kg 6.8
/II
Bosch Power Tools
30/04/13 14:06