Bosch AdvancedCut 50 Manual Original página 15

OBJ_BUCH-2772-002.book Page 14 Wednesday, August 24, 2016 2:29 PM
14 | English
13 Vacuum connection
14 Wing bolt for setting the bevel angle(AdvancedCut 50)
15 SDS saw blade receptacle
16 Splinter guard
17 Depth stop A
18 Depth stop B
19 Hood for dust extraction(AdvancedCut 50)
Technical Data
All-purpose saw
Article number
"Cut Control"
Speed control
Speed preselection
Rated power input
Output power
Max. cutting depth*
– without depth stop
– with depth stop A
– with depth stop B
– with depth stop A and B
Bevel angle (right), max.
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
* The resulting cutting depth is dependent on the saw blade used. The values stated here are based on the NanoBlade Wood Basic provided.
Noise/Vibration Information
Sound emission values determined according to
EN 62841-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11: Sawing chip-
2 2
board: a =2.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 62841 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However, if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
1 609 92A 3GE | (24.8.16)
20 Guide-rail adapter(AdvancedCut 50)
21 Lock for guide-rail adapter(AdvancedCut 50)
22 Guide rail*(AdvancedCut 50)
23 Bevel-angle scale(AdvancedCut 50)
24 Saw blade storage
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organise work patterns.
Assembly
 Before any work on the machine itself, pull the mains
Replacing/Inserting the Saw Blade
.  Make sure that you do not hold the power tool in the
 Do not pull on the chain and do not pull the chain off the
 Always replace a complete saw blade with a complete
Selecting a Saw Blade
 Use only clean saw blades. Ensure that the SDS saw
Use only saw blades suitable for the material being worked.
 Avoid skin contact when you want to replace a saw
EasyCut 50 AdvancedCut 50
3 603 CC8 0..
W 500
W 370
mm
mm
mm
mm
°
kg
plug.
area of the On/Off switch when changing the saw
blade. There is danger of injury when unintentionally actu-
ating the On/Off switch.
guide unit!
saw blade! The chain cannot be replaced on its own.
blade holder is also free of chips and sawdust.
blade and wear protective gloves. The saw blade can be-
come hot during prolonged use.
3 603 CC8 1..
 
 

–
500
370
50 50
36 36
22 22
6 6
– 45
1.6 1.7
/II /II
Bosch Power Tools