Publicidad
Idiomas disponibles
Idiomas disponibles
SPECIAL REQUIREMENTS:
There may be General or State Occupational Safety and
Health Administration (OSHA) regulations, local codes or
ordinances that apply to the intended use of the product.
Please consult a qualified electrician, electrical inspector, or
the local agency having jurisdiction:
„ In some areas, products are required to be registered with
local utility companies.
„ If the product is used at a construction site, there may be
additional regulations which must be observed.
INSTALLING/REMOVING BATTERY PACKS
See Figure 2.
The power station has a total of eight battery ports, but will
function even if only one battery pack is installed. The more
batteries installed, however, the greater the amount of power
available and/or length of run or charge time provided, up to
the full capacity noted in the Product Specifications section
of this manual. For best performance, use at least four 4Ah
or greater batteries.
Battery packs are shipped in a low charge condition and
should be charged before first use.
To install:
„ Insert a battery pack into the power source as shown.
Make sure the latches on the battery pack snap into place
and the battery pack is secured in the power source be-
fore beginning operation.
„ Repeat to install additional battery packs as desired.
To remove:
„ Depress the latches on the battery pack and remove.
CHARGING THE POWER STATION
See Figures 2 - 4.
„ Install the desired number of battery packs.
NOTE: If not using all of the available battery slots, the
location of the batteries installed does not matter and will
not affect power station charging performance.
„ Connect the charger cord to the power station, then plug
the charger into a standard electrical outlet that is nominal
120/60 Hz AC (typical U.S. household type circuit).
„ Once the charging cable is connected and plugged in,
sequential charging of the batteries will begin.
NOTE: If connecting the charger immediately after using
the power station at a high AC load, the battery tempera-
ture may be outside the acceptable charging range and
cause the LCD display to show an error condition. If this
occurs, charging will begin automatically once the battery
temperature reaches an acceptable level.
An LED light located at the top of each battery port will
indicate the status of each battery. Refer to the Battery
Port LED Functions chart for a description of the lights.
In addition to the LED indicator, the LCD screen will also
OPERATION
provide information about the battery and charging status
of the power station.
USING THE POWER STATION
See Figure 5.
To power the product on:
„ Press and hold the main power button for two seconds
to turn the product on. This will activate the LCD display
and allow the USB charging ports and LED task light to
be used.
NOTE: The main power button will illuminate when power
to the unit is on.
To use the AC outlets:
„ After powering the product on, press and hold the AC
output button to activate the AC outlets.
NOTE: For normal operation of the power station, the main
power button and the AC output button (if using AC outlets)
will be solid green and there will be one audible beep. If any
other light pattern or beeps occur, refer to the Alert Func-
tions chart that follows.
Sleep mode:
„ After 30 minutes of inactivity, the product will enter into
sleep mode. In this state, the main power button LED will
blink slowly and the LCD screen will turn off. All unit func-
tion is disabled to conserve power, but the Bluetooth
connection will remain active.
NOTE: Sleep mode will not occur if the AC output but-
ton is ON.
„ Press the main power button to end sleep mode.
Automatic shut-off:
„ The power station will automatically power off after
12 hours of inactivity. The Bluetooth
disabled at this time.
To manually turn the product off:
„ Press and hold the main power button for two seconds.
WARNING:
While operating, maintain clearance on all sides of this
product. Do not block vents or allow the product to
overheat.
GENCONTROL
See Figure 6.
NOTE: The LCD display will not work unless the product is
powered on.
Battery charge level:
The battery charge level indicator shows how much charge
is remaining in the battery.
Load level:
10 — English
connection is also
®
LCD DISPLAY
™
®
Publicidad
