urmet domus Digivoice 1138/18 Manual De Instrucciones página 6

1
1
1
A
1
9
10
0
1
GENERAL
The special door phone Ref.11 /1 is used
exclusively in the IGIVOICE system. It provides
the following features:
communication service towards calling spea ers
communication service towards all calling door phones
with no answer call storage capacity up to 10
communication service towards all door phones
called by the user by entering a code or,
alternatively, up pressing a programmed button.
The special door phone belongs to the
line. A single version which can be table or wall
fi tted see Installation is provided.
: Any calling modules Ref. 10
10 /15, 10 /16 installed in systems with special
door phones Ref. 11 /19 MU T BE version .0 or
higher.
10
ER R AN E L
1
Integrated signal decoder.
1
ifferentiate calling tone for calls from main
stations, secondary stations, indoor stations,
switchboards or oor calls.
edicated switchboard call button.
oor open LE signal.
1
Mute function.
Automatic door opener function.
Call volume ad ustment.
11
Video module management.
loor call button management.
a e up function from any main or secondary
9
calling station on the riser by means of a dedicated
button.
Call reception from other door phones.
ossibility of inhibiting calls from door phones
with respective LE signal.
ossibility of storing answered calls received from
door phones up to 10 with respective LE signal.
ossibility of calling any indoor station in the
system by entering the code or, alternatively,
pressing a programmed button up to 0 .
ossibility of sending special codes.
rogramming via device eypad with LE signals.
rogrammable call repeat terminal.
AR L
19
1 oor phone hood.
Ten ey alphanumeric eypad for code dialling.
dialled code delete button.
BELL call button.
5 I T button for alphabetic codes.
6 IGIVOICE switchboard call button.
1
andset.
Call volume ad ustment trimmer.
9 pea er breathers.
10 MUTE button.
11 Two colour LE signalling MUTE green fi xed ,
automatic door opener
programming red or green/red
data line green/red ashing .
1 Call from other door phone in progress LE
fi xed red , stored call from door phone red
ashing , calls from door phone disabled one
ash every three seconds .
1 A E U button.
1 OOR O E signalling LE .
15 OOR O E button.
CAITEL
16 andset lever.
1 all fastening holes.
1 Rubber table feet.
/10,
19 Connection wire passage hole.
0 Table stand.
N ALLA
The special door phone can be table or wall fi tted.
all fi tted versions can be fi tted by the side of a
video module 1
The electrical connections are made on the terminal
board directly fi tted inside the special door phone:
logic power positive input
0 logic power negative input
data line
A voice out
voice bac
voice power positive input
0 voice power negative input
0 logic power negative input
oor call button input
video brac et control output
R supplementary call ringer control output.
A LE N ALLA
The special door phone is set at the factory to be
table fi tted. The table stand
1 ensure a perfect inclination.
ALL N ALLA
The special door phone is set at the factory to be
table fi tted. roceed as follows for wall fi tting:
1 Remove the table stand
Remove the glued rubber feet 1 .
Open the door phone.
Brea through hole 1
5 asten to the wall by means of the two bolts pro
vided and holes 1 .
nstalling video module 1732/1
green ashing ,
The video module, provided with a brac et 1
ashing , no
can be wall fi tted to the left of the special door
phone by means of the L plate provided with the
brac et 1 /9 .
11 00 11 00
N N G RA
or correct operation, the special door phone needs
to be confi gured upon installation.
/1. The programming operation consists in assigning
parameters to the various operating variables
se uentially.
tart the confi guration cycle according to the
instructions below:
After selecting each parameter, press the CALL
button
The system will chec the set data and re ect
incoherent data.
Use the delete button
confi rming.
ress button
The cycle will end after the last confi guration step.
old
1 until LE
confi guration cycle.
N
E 1
0 and rubber feet The permissible values are 1
1 or
followed by
to indicate that the data has been stored.
N
E 2
0 . The permissible values are 1
11 will ash once to indicate that the data has
been stored.
on the top. The special door phone code must be uni ue in the
system. There cannot be two special door phones
with the same code. A special door phone cannot
have the same code as an indoor station or a
switchboard.
/9 ,
E 3
The busy time must coincide with time programmed
on the call module. The permissible values are 1
indicating 10
to indicate that the data has been stored.
E
The call ring time is time for which the indoor
stations ring when they are called by the special
door phone.
LE
been stored.
N
to confi rm.
to correct error before
to accept previous settings.
I T 5 pressed and repeatedly press button
11 comes red fi xed to start the
E AL R NE R ER
, 1, . To program
, press 1 followed by I T CALL or
I T CALL. LE 11 will ash once
E AL R NE E
, 1, . LE
E
0 seconds. LE 11 will ash once
ALL R NG E
ermissible values are 1 5 seconds.
11 will ash once to indicate that the data has
11