Safety 1st FLAT STEP Guia De Inicio Rapido

min 73cm - max 80 cm
min 28.7" - max 31.5"
©2020 Dorel Juvenile Group, Inc. Safety 1st™ and the Safety 1st logo and design are trademarks of
Dorel Juvenile Group, Inc. Safety 1st™ y el logotipo de Safety 1st y su diseño son marcas comerciales
de Dorel Juvenile Group, Inc. (800) 544-1108 www.safety1st.com. Styles and colors may vary. Los
estilos y los colores pueden variar. Made in CHINA. Hecho en CHINA. Distributed by (distribuido por)
Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494. Dorel Juvenile Canada, 2855
Argentia Road, Unit 4, Mississauga, ON L5N 8G6. Importado y Distribuido en Chile por: Comercial e
Industrial Silfa S.A. - San Ignacio 0201 / Parque Industrial Portezuelo Quilicura, Santiago Chile. Fono
(562) 2339 9000. En Perú por: Comexa S.A. - Los Libertadores 455 – San Isidro, Lima – Perú. Fono
(511) 4469014. En Centro América, Caribe y Ecuador por: Best Brands Group S.A. – Av. Balboa, Bay
Mall Plaza, Planta Baja, local 9, Panamá. - Fono: (507) 300 2884. En Colombia por: Baby Universe
S.A.S. - Vía 40 No. 77-29, Barranquilla, Colombia - Fono: (575) 353 1110 Importador: DJGM, S.A. DE
C.V. Gabriel Mancera No. 1041 Col. Del Valle, Benito Juárez C.P. 03100 México, Ciudad de México
R.F.C. DJG140305GN9 Tel. (55) 67199202 11/16/20 4358-7459A
Care and Maintenance:
DO NOT immerse in water. Wipe with a damp cloth
and dry.
Before you begin
1
To Install
Insert all 4 pressure post assemblies in the proper locations.
x2 x2
A
A
B
To Use
4
5
Keep this instruction sheet for future reference, as it contains important information.
Children have died or been seriously injured when
gates are not securely installed.
• Keep small parts away from children during assembly.
• ALWAYS install and use gates as directed using all
required parts.
• You MUST install wall cups to keep the gate in place.
Without wall cups, child can push out and escape.
• STOP using when a child can climb over or dislodge
the gate.
• Use only with the locking/latching mechanism
securely engaged.
FLAT STEP
Parts List
GATE
Age: 6 to 24
• Remove all contents from packaging and
discard box, and/or poly bags.
months.
Adult assembly • Lay out all parts.
required.
• Do not return this product to the place
of purchase. To address any issues or for
helpful information on assembly/installation
or use, please visit us at www.safety1st.com
to chat with us there. You can also text us
at (812) 652-2525 or call Consumer Care
at (800) 544-1108. Have ready the model
number (GA119) and date code (manufacture
GA119 date) located on inside of gate panel.
• Tools Needed:
Phillips head screwdriver (not included)
Hex wrench tool (included)
Extension caps
CHECK TO MAKE SURE THE
A
EXTENSIONS CAPS ARE IN
THE PROPER LOCATIONS
(see Parts List)
B
2
Install wall cups
2a
x2
B
Remove paper
backing from one
A
side.
2d
Place wall cup
on bumper.
2g
Remove gate.
B
NOTE: Position gate on the floor and center gate when
adhering each of the 4 wall cups. Follow procedure in
step
3
Open gate
A B
LOCKED
2
1
Close gate
A B
UNLOCKED
WARNING:
• NEVER use to keep child away from pool.
• Discontinue use of the gate if it becomes damaged,
broken, or disassembled.
• Intended for use with children from 6 months through
24 months.
• Install according to manufacturer's instructions.
• TO PREVENT FALLS, NEVER use at top of stairs.
• ALWAYS install as close to the floor as possible.
• This product will not necessarily prevent all accidents.
NEVER leave child unattended.
• Gate is not meant to replace proper adult supervision.
OK
A
x4
Wall cups
x4
Adhesive pads
x4
Screws
A
B
B
OK NO
DO NOT REMOVE THE ZIP
TIE UNTIL INSTALLATION IS
COMPLETE
2b 2c
Adhere to outside Remove paper
of wall cup. backing from
other side.
2e 2f
Insert bumper into With gate on
gate.
the floor, touch
wall cup to wall.
2h 2i
Repeat for 3
other wall cups.
Fasten each
wall cup with
screw.
to install gate into wall cups.
Optional:
Using the swing stops
Gate will swing both ways unless one
of the swing stops is down. Gate will
not swing at all if both swing stops
are down.
UNLOCKED
LOCKED
Click
• ALWAYS check regularly to ensure gate and locking
systems are secure. Tighten locking hardware as necessary.
DO NOT over-tighten.
• DO NOT use gate if any parts are missing or broken. Contact
Dorel Juvenile Group for replacement parts and instructional
literature if needed.
• DO NOT use any replacement parts not provided by Dorel
Juvenile Group.
• DO NOT substitute parts or try to modify the product in any
way. Parts not provided and approved by Dorel Juvenile
Group may result in an unsafe product.
3
Using the SecureTech indicator
TM
If you see RED, the gate
is not locked OR it has
A
become unpressurized.
A B C
B
When you see GREEN,
C
the gate is locked and
pressurized.
D
D
CAUTION:
Top Post
Assembly
x2
A
x2
Hand tightening nut
Bottom Post
Assembly
Hex
x2
B
Hex wrench tool
(RED) (GREEN)
UNLOCKED LOCKED
B
D