Publicidad
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
DANGER:
THE POWER MUST BE TURNED OFF AND THE UNIT DISCONNECTED FROM
THE POWER SOURCE WHENEVER PERFORMING SERVICE, MAINTENANCE
FUNCTIONS OR CLEANING THE REFRIGERATED AREA.
DANGER:
NEVER USE A HIGH PRESSURE WATER WASH FOR THIS CLEANING
PROCEDURE AS WATER CAN DAMAGE THE ELECTRICAL COMPONENTS
LOCATED NEAR OR AT THE CONDENSER COIL.
DANGER:
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
REFRIGERATORS AND FREEZERS
The interior and exterior can be cleaned using soap and warm water. If this isn't
sufficient, try ammonia and water or a nonabrasive liquid cleaner. When cleaning
the exterior, always rub with the "grain" of the stainless steel to avoid marring
the finish.
Do not use an abrasive cleaner because it will scratch the stainless steel and
plastic and can damage the breaker strips and gaskets.
CLEANING THE CONDENSER COIL
The condenser coil requires regular cleaning. Recommended cleaning is every
90 days. In some instances, you may find that there is a large amount of debris
and dust or grease accumulated prior to the 90 day time frame. In these cases
the condenser coil should be cleaned every 30 days.
If the build up on the coil consists of only light dust and debris, the condenser
coil can be cleaned with a simple brush. Heavier dust build-up may require a
vacuum or even compressed air to blow through the condenser coil.
If heavy grease is present, there are de-greasing agents available for refrigeration
use and specifically for the condenser coils. The condenser coil may require a
spray with the de-greasing agent and then blown through with compressed air.
Failure to maintain a clean condenser coil can initially cause high temperatures
and excessive run times. Continuous operation with dirty or clogged condenser
coils can result in compressor failures. Neglecting the condenser coil cleaning
procedures will void any warranties associated with the compressor or cost to
replace the compressor.
In order to maintain proper refrigeration performance, the condenser fins must
be cleaned of dust, dirt and grease regularly. It is recommended that this be
done at least every three months. If conditions are such that the condenser is
totally blocked in three months, the frequency of cleaning should be increased.
Clean the condenser with a vacuum cleaner or stiff brush. If extremely dirty, a
commercial-grade condenser cleaner may be required.
STAINLESS STEEL CARE AND CLEANING
To prevent discoloration of rust on stainless steel several important steps need to
be taken. First, we need to understand the properties of stainless steel. Stainless
steel contains 70-80% iron which will rust. It also contains 12-30% chromium
which forms an invisible passive film over the steels surface which acts as a
shield against corrosion. As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside elements can begin to
breakdown the steel and begin to form rust of discoloration. Proper cleaning of
stainless steel requires soft cloths or plastic scouring pads.
4
GLASS DOOR ICE MERCHANDISER
SWING DOOR REPLACEMENT AND ADJUSTMENT
1. Open the bottom panel and hold the door. Then loosen the bottom hinge
screw and take off the old door.
2. Prepare new door; insert top pin into top hinge, get one bottom hinge to hold
the door with the bottom pin. Fasten bottom hinge securely to the door frame
with three screws.
3. Allow the door to freely swing, making sure it swings closed by itself with no
restriction.
4. Plug the unit in and make sure the lock works well.
5. If not, adjust the door height by adding the plastic spacer/washer provided
with the bottom hinge pin.
SLIDING DOOR REPLACEMENT AND ADJUSTMENT
1. Take off the hook of the counterweight of door from the top of the door.
2. Hold the door up until the bottom edge is over the channel. Move the door
out across the channel and lay the door down.
3. Prepare new door; hold the door insert into top channel until the bottom
edge is over the bottom channel. Slide the bottom of the door across the
channel wall and place it into the channel.
REMOVE THE BOTTOM PANEL
Loosen and remove the top screws, slide the panel up and out
LIGHT BULB REPLACEMENT
1. Upper light bulb replacement: Loosen the screws in the bottom of the top
panel and swing the panel up until the light bulb is exposed. Light bulb can
then be changed.
2. LED light bulb replacement: Take the cover off to replace the LED light bulb.
Publicidad
