Publicidad
Installation
Mounting the module
To mount the module inside the xGenConnect, follow the steps
shown in Figure 3.
Connecting the module
Connect the module to the xGen bus using the xGen bus
terminals (Figure 2, item 3).
Use 2-pair twisted shielded data cable such as WCAT52 or
WCAT54 to connect the module to the xGen bus.
The module provides terminals for zone inputs, and
auxiliary/common for power. Power is taken from the xGen
bus. Refer to xGenConnect Installation and Programming
Manual for current limitations for the relevant standard.
Put a TERM jumper (Figure 2, item 5) on the first and the last
module on a cable run to ensure correct RS-485 termination
and to avoid communication issues with signal reflection, etc.
Wire the sensors to the zone inputs. See xGenConnect
Installation and Programming Manual for details.
Enrolling the module
Automatic enrollment
Push and hold the enrollment button on the xGenConnect
panel for 2 seconds. The panel is now in automatic enrollment
mode and will search for the new module.
If the enrollment is successful, the CONFIG LED will blink once
every 2 seconds.
Manual enrollment
Follow these steps to enroll the module:
1.
Login to the xGenConnect panel via panel web server as
installer.
2.
Click Advanced > Devices > System Devices > Control >
Device 1.
3.
Go To Enroll Function.
4.
Select Manual enroll.
5.
Click Save.
6.
Press and hold the LEARN button (Figure 2, item 6) until
the CONFIG LED (item 7) blinks, then release the button.
Proceed to programming the system and the additional
modules. See xGenConnect Installation and Programming
Manual for details.
Firmware
The module firmware is remotely upgradeable using DLX900
or locally with a USBUP via the USBUP port on the module
(Figure 2, item 4).
Specifications
Compatibility
xGenConnect security system
Voltage
12.0 to 13.5 VDC (provided by panel)
Current
30 mA (typical)
2 / 14
Auxiliary output
Provided by xGen bus, max. 400 mA
PCB dimensions
153 x 57 mm
PCB weight
0.06 kg
0 to +49°C (+32 to 120°F)
Operating temperature
−34 to +60°C (−30 to +140°F)
Storage temperature
Relative humidity
up to 85% noncondensing
Regulatory information
Manufacturer
Placed on the market by:
Carrier Fire & Security Americas Corporation Inc.
13995 Pasteur Blvd
Palm Beach Gardens, FL 33418, USA
Authorized EU manufacturing representative:
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
Certification
EN 50131-3 Control and indicating equipment,
Security Grade 2, Environmental class II.
Tested and certified by Telefication B.V.
European Union
Carrier Fire & Security hereby declares that this
directives
device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see firesecurityproducts.com.
REACH
Product may contain substances that are also
Candidate List substances in a concentration
above 0.1% w/w, per the most recently published
Candidate List found at ECHA Web site.
Safe use information can be found at
https://firesecurityproducts.com/en/content/intrusio
n-intro
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
recyclethis.info
Contact information
www.firesecurityproducts.com/en/page/caddx
P/N 466-6819-ML • REV C • ISS 22MAR21
Publicidad
