GLOBBER ELEMENT Serie Manual Del Usuario página 6

Keep the instructions for future.
NF-EN-14619: 2019
READ THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER BEFORE
USING. MAXIMUM WEIGHT: 100 KG
Warnings
- The Scooter is suitable for adolescents and adults. It is not a toy, but sports
equipment for physical training, it is not intended for use in extreme sports such as
jumping, ollie ramps, etc. This product should never be used at a skate park for an
"aggressive" use (challenging skateboarding moves, etc.).
- U se with caution on a flat, clean, dry surface and, if possible, away from other
users, and obey the road safety rules.
- C heck local laws regarding scooter use, respect all the traffic rules and signs.
Stay away from other pedestrians or users on public roads.
- B est when used on a flat, dry surface free of gravel and grease. Avoid bumps and
drainage grates that might cause an accident.
- Warning! Protective equipment consisting of wrist protectors, gloves, knee pads,
helmets and elbow pads should be worn.
Using the scooter
• Before and after each use: To prevent pinched fingers, carefully follow the
instructions of unfolding and folding. Make sure that the locking mechanisms are
securely locked:
- Check the height of the steering system and make sure that the nuts are
tightened and the handlebars and front wheel are perpendicular.
- Check all of the connection elements: the brake, the quick release system of the
steering column and the wheel axles must be correctly adjusted and must not
be damaged.
- Also check the tire wear.
• Braking:
- A brake is located at the rear, when necessary, press down on it to slow down.
Press down gradually to prevent skidding or loss of stability. The metal brake may
heat up after multiple uses. Avoid touching it during and after use.
Assembling the product
- The folding and unfolding operations of the scooter are to be done by a single
person.
- D uring these operations, be careful you do not get your fingers stuck in the hinge
and locking system.
- Make sure that the locking devices are properly engaged.
6
1 - Unfold the scooter
D1: Unpack the folded-up scooter from its box.
D2: Push in the button. At the same time, pull the metal part, which will cause the
handlebars to open. Then straighten the steering column until the button locks
into position.
(If it is difficult to fold or unfold scooter while operating, please use M4 allen tool
to loose hex screw one turn as the photo showed. Don't loose the hex screw too
much; the hex screw will be lost.)
D3: Open the clamp lever on the T-bar. Remove the plastic insert. Pull out both
parts of the T-bar handle from the double clips. Press in the spring loaded buttons
and insert both into the tubes of the T-bar. Wiggle and turn a bit until their spring
loaded locking buttons align with the holes and fix the whole steering bar assembly
in place. Close clamp lever.
Warning! Risk of injury by pinching!
Do not insert your fingers into the shaded area indicated
2 - Adjust the handle bar
D4: Open the fixing lug. Then press down the spring loaded locking button and pull
the handlebar up or push it down with the other hand.
Choose the suitable locking hole and make sure the spring loaded locking pin
snaps securely in place. The adjustable T-bar handle can be adapted in height to
suit the rider.
4 different positions are available.
Lock the fixing lug tight and securely when you have finished adjusting the height.
3 - Fold up the scooter
D5: Lift up the kick stand. Push in the button while pulling on the metal part, which
will cause the steering column to close. Release the button when the steering
column begins to fold up. The button will position itself in its locking position when
the steering column is completely folded.
D6: For purposes of storage, remove both parts of the T-bar handle from the T-bar.
Open the clamp lever on the T-bar. Press down the spring-loaded locking pins
while pulling out the part sideways at the same time. Strings inside the tubes will
hold the individual part together. Clip the two parts of the T-bar handle into the clips
to both sides of the steering bar (refer to D3 in reverse order). Close clamp lever.