Publicidad
Idiomas disponibles
Idiomas disponibles
ROUGH-IN
DIMENSIONS
6O
_(152.4)
4
243/4
_,
1
(62.9)
_(2.54)
SIDE
Power
Cord
331/2
(85)
inch (cm)
Adjustable Legs
263/4
36
(91.5)
Water
Inlets
Under
31¾
Counter
(80.3)
34%
(87.9)
T
BACK
UNDER COUNTER INSTALLATION
If an under counte¢ ' installation is desired, the washer MUSThave a
top sheet kit installed, P/N 131445600,
Kit
is available
from
an
authorized
parts
distributor,
_'Custom sized countertop
is required,
243/4
(62.9)
SIDE
-(2.54)
Power
Cord
33t/2
(85)
inch (cm)
Adjustable
Legs
263/4
36
(91.5)
Ul
(8
\j
BACK
l
LOCATION
OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside weather
conditions, The ambient temperature
should never be below 60
degrees F (15,6 degrees C) for proper washer operation,
2. In an area where it will come in contact with curtains or drapes,
3. In an area (garage or garage-type building) where gasoline of
other flammables are kept or stored (including automobiles
4. On carpet, Floor MUSTbe
solid with a maximum slope of 1/2 in,
per toot (1,27 cm per 30,5 cm), To ensure vibration or movement
does not occur, reinforcement
of the floor may be necessary,
IMPORTANT
MINIMUM
INSTALLATION CLEARANCES
When installed
in alcove or closet:
Sides, Rear = 0 in, (0 cm)
Top = 0 in, (0 cm) Front Console Model
Top = 15 in, (38,1 cm) Rear Console Model
When installed
in closet: Front = 1 in, (2,54 cm)
Closet door ventilation required:
2 Iouvered openings each 60 in2
(387 cm2), 3 in, (7,6 cm) from top
and bottom of door,
UNPA CKING
1. Cut the shipping carton
along the dotted line along
the base of the unit,
2. While in the carton
carefully lay the washer
on its back side,
3. Remove the styrofoam
::i
base,
iii
4. Carefully return the
washer to an upright
position and remove
the carton,
5. Carefully move the
washer to within 4 feet
_
BOlT
(122cm) of the final location,
(_)
6. Remove the following
from
_
SPACER
the back side of the washer:
(_)
_
)
CLAMP
3 bolts,
3 yellow plastic spacers,
2 or 3 metal "P" clamps
7. Remove the service panel from
the front of the washer,
8. Remove the 4 nuts and
6 large washers that attach
the 2 yellow shipping braces
to the drum and the
base, Lift up on the
drum and remove
the braces (a yellow
ribbon surrounds the
items to be removed),
(_) o
/
These braces must be
(_
removed to allow the
,J
power supply cord to
_::::::_
be released from the
(_
shipping ring,
j(_
9. Remove the large
styrofoam block located
under the drum, Lift up on the
drum, tilt the base of the foam block inwards toward the rear of
the washer until free, then pull it out,
10. Remove and discard the yellow ribbon and label from the
front of the washer,
11. From the rear of the washer, carefully pull out the power supply
cordthrough
the hole in the backsheet,
12. Replace the service panel and screws,
NOTE: If the washer isto be transported at a later date, the shipping
support hardware must be reinstalled to prevent shipping damage,
Retain the hardware in the plastic bag provided.
Publicidad
