Dual CS 741 Q Manual Del Usuario página 10

In order to replace the cartridge you must place it from below
against the head shell so that the front edges are flush. Please
ensure that the cartridge lies absolutely flat on the head shell
before pulling the tonearm lift to the front in order to.lock it
in position (Fig. 12). You may then, if desired, reinsert the
safety screw (Fig. 11/(11))
Stylus
The stylus is subject to natural wear and tear during normal
playing. Therefore, we recommend you occasionally check the
stylus and, in the case of diamond styli, this should be carried
out after approximately 300 playing hours. Your specialist
dealer will be pleased to do this for you free of charge. Worn
or damaged (splintered) styli chisel the modulation from the
grooves and destroy records. Therefore, only use as replacement
the stylus types recommended in the technical data of the
cartridge. Imitated styli result in audible quality losses and in-
creased wear and tear of records. Please remember that, for
physical reasons, the stylus holder with the diamond stylus is
extremely fine and must therefore be necessarily sensitive to
impacts, shocks or uncontrolled movement.
When removing the stylus please note the information contained
on the separately enclosed data sheet referring to the cartridge
on your unit.
Installing of 1/2-inch cartridge
Your Dual turntable will provide excellent tracking and re-
production if used in conjunction with ULM (Ultra low mass)
cartridges. However the tonearm characteristics are so good
that even substantially heavier 1/2" cartridges will operate
optimally. If you wish to fit a standard 1/2" cartridge, please
proceed as follows:
4) Connect the connections of the head shell to the connecting
pins on the cartridge. The connections are color-coded:
Red R right channel
Green RG right channel ground
Blue GL left channel ground
White L left channel
Avant de mettre votre platine en marche pour la première fois,
lisez attentivement cette notice d'emploi. Cela vous évitera de
commettre des erreurs de branchement ou de commande et
d'endommager votre appareil
Les éléments de commande
(1) Contrepoids du bras avec antirésonateur de tuning
(2) Vis de blocage du contrepoids du bras de pick-up
(3) Supports du couvercle
(4) Réglage de la force d'appui du bras
(5) Réglage de la vitesse de descente du bras de pick-up
(6) Vis d'ajustage de la hauteur du bras
(7) Réglage d'antiskating
(8) Vis d'ajustage du point de pose du bras
(9) Support du bras avec surface d'appui
(10) Réglage de la vitesse du plateau
(11) Vis de fixation de la cellule
(12) Poignée du bras / Verrouillage de la tête de lecture
(13) Touche pour lever le bras a et descendre le bras w
12
Cartridge - Total weight - Including hardware
upto 6g 1 thin disc
upto 7g 1 thick disc
upto 9g 1 thick disc and 1 thin disc
up to 10g 2 thick discs
Screw the smaller thread of the special screw into the coun-
terweight (1). With the bevelled side to the outside, screw
the corresponding additional weights onto the thicker part
of the screw.
7) Now once again carefully balance the tonearm as described
in the section "Balancing the tonearm"' and set the stylus
pressure and anti-skating force required for your cartridge,
After having mounted a 1/2 inch cartridge check the height of
the playing needle above the record with the pick-up arm lift
in position a also check that the needle lowers into the run-in
groove of the record. See parts 'Cue control (Pause) (page 11)
and "Adjustment of tonearm indexing" (page 11).
Servicing
All the lubrication points have sufficient oil. Thus, your unit
will operate impeccably for many years under normal condi-
tions. Never try to lubricate any of the lubrication points your-
self. If your record player should ever need servicing, either
take it to your specialist dealer or ask him for the address of
the nearest authorized Dual Servicing Workshop. Please make
sure that only original Dual replacement parts are used.
Should the unit ever be dispatched, make sure that this is
packed perfectly, if possible, by using the original packaging.
The platter
Important! Remove the platter before transporting the unit!
Subsequent transport
Electrical safety
The unit complies with the International
Safety Regulations
for radio and related devices (IEC 65).