Publicidad
Enlaces rápidos
Model #
900Wc
Seneca Side Table
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions and Finishing Hints before you begin your
project.
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: 541-687-2060
CALL US FIRST! Do not return this item to the store
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
P.O. Box 2827
Eugene, OR 97402 USA
IMPORTANT NOTES:
• For normal household use only. Not recommended for
commercial use.
•
Do not climb, sit or stand on this unit.
•
Unload items before you move this unit.
•
Do not overload the shelf or drawers.
• Before you begin your project, completely read the
Assembly Instructions and Finishing Hints.
• Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
• Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm.
California Health and Safety Code Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
To Order: Provide the furniture model number (upper
portion of this page), the part letter, production code,
quantity needed, reason for replacement and your full
name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
Production Code:
VN
WARNING
12/13
Publicidad
Manuales relacionados para Whittier Wood Furniture Seneca 900Wc
Resumen de contenidos para Whittier Wood Furniture Seneca 900Wc
- Página 1 Model # 900Wc IMPORTANT NOTES: Seneca Side Table • For normal household use only. Not recommended for commercial use. • Do not climb, sit or stand on this unit. Assembly Instructions • Unload items before you move this unit. • Do not overload the shelf or drawers.
- Página 2 900Wc Seneca Side Table — Parts List Please identify the parts and check that quantities received match what is on this list. If you need to replace a part, refer to the following letter and item name. 8 x 30mm Wood Dowel (14 inserted) Wood Knob Drawer Stop...
- Página 3 900Wc Seneca Side Table Assembly Instructions Tools Required: Phillips Screwdriver, Mallet or Padded Hammer, Wood Glue Fig. 1 The backs of the Left and Right Side Assemblies are grooved. Spread a thin layer of glue in the dowel holes in the Left Side Assembly (Rb). Making sure the curved edge of the front stretcher faces the front of the unit and all pocket drilled holes face down, insert the Front Stretcher (J), Back Stretcher (K), and Shelf (L) into the Left Side Assembly (Rb).
- Página 4 Fig. 3 Fig. 3a Apply a light film of glue in the two dowel holes at each side on the bottom of the Top (H) and slide the Top down over the dowels in the Sides (Qb and Rb). Using the pocket drilled holes as guides, fasten in place with #8x1-3/16"...
- Página 5 Fig. 5a Fig. 5 Slide the Drawer Bottom (M) into the grooves in the sides and front. See Figures 5 and 5a. Fig. 6a Fig. 6 Attach the Drawer End (O) to the Drawer Sides (Pb) with #8x1-3/16" Pan Head Screws (S). See Figures 6 and 6a.
- Página 6 x 10 Fig. 7 Attach the Back (Ic) with #6 x 5/8" Philtruss Screws (T) through the predrilled holes. See Figure 7. Fig. 8 Insert the upper drawer half way into the unit and insert two Dowels (D) into the holes near the front edge of the top.
- Página 7 Fig. 9 Turn the unit upside down on a clean, protected surface and insert the bottom drawer. See Figure 9. Fig. 10a Fig. 10 Center and align the Drawer Stop (G) to the bottom edge of the Front Stretcher and attach with two #6 x 5/8"...
- Página 8 Modelo # 900Wc NOTAS IMPORTANTES: • Para uso de viviendas normales únicamente. No se Mesa Lateral Seneca recomienda para uso comercial. • No se suba, no se siente ni se pare sobre este mueble. Instrucciones de ensamblar • No mueva este mueble mientras esté lleno. Vacíelo antes de moverlo.
- Página 9 900Wc Mesa Lateral Seneca Lista de piezas Identifique las piezas y verifique que las cantidades que recibió coincidan con las de la lista. Si necesita reemplazar una pieza remítase a la siguiente letra y nombre de la misma. Parte Descripción Cantidad Parte Descripción...
- Página 10 Añada la parte posterior (Ic) con tornillos Philtruss #6 x 5/8" Glue all dowels this step = Una con pegamento los (T) en los huecos pre-taladrados. Ver Figura 7. taquetes durante este paso. Aplique una capa fina de pegamento en los dos huecos para los taquetes en la cara oculta de la parte superior Inserte el cajón superior hasta la mitad en la unidad e inserte (H).
- Página 11 No. De Modèle 900Wc REMARQUES IMPORTANTES : Table d'appoint Seneca • Pour un usage domestique uniquement. Non recommandé pour un usage commercial. Instructions d’assemblage • Ne pas monter, s’asseoir ni se mettre debout sur cet article d’ameublement. • Ne pas déplacer cet article d’ameublement s’il est chargé. Le décharger avant de le déplacer.
- Página 12 900Wc Table d’appoint Seneca Liste des pièces Veuillez identifier les pièces et vérifier que les quantités reçues correspondent à la quantité indiquée sur la liste. S’il faut remplacer une pièce, consulter la lettre qui figure ci-dessous et le nom de l’article. Pièce Description Qté...
- Página 13 Glue all dowels this step = Collez toutes les goupilles Fixez le dos (Ic) avec les vis Philtruss no 6 x 5/8 po (T) à cette étape. dans les orifices pré-perforés. Voir Figure 7. Appliquez un léger film de colle dans les deux trous de goupille dans le côté...
- Página 14 Whittier Finishing Hints instructions call for a slow drying glue. Carefully read the Checklist of materials label and instructions of the glue manufacturer. Your unit □ □ □ Rubber gloves Tack cloth #220 & #320 may not need glue. □ □...
- Página 15 Whittier Finishing Hints Preparing the surface apply additional coats. Lightly sand and wipe surface with a lint-free rag or tack cloth between coats. 1. Sand each piece with #220 grit sandpaper. Sand with the grain of the wood on flat surfaces and opposite the 4.
- Página 16 Consejos de Whittier para terminaciones Consejos de pegado Lista de control de materiales Estos son algunos consejos generales. Consulte las □ □ □ Guantes de Paño de Papel de lija instrucciones de ensamblaje para obtener información detallada hule adherencia No. 220 y No. sobre cómo pegar el producto específico que utilice.
- Página 17 Consejos de Whittier para terminaciones Consejos para las terminaciones Aplicación de la capa de acabado Utilice productos de la misma marca para garantizar la Siempre debe leer y seguir las instrucciones de la etiqueta. compatibilidad. No se recomienda mezclar terminaciones a Mezcle suavemente el preparado para la capa de acabado, base de solventes y a base de agua.
- Página 18 Conseils de finition de Whittier Conseils en matière de collage Liste de vérification des matériaux Cette section contient des conseils d'ordre général. Veuillez vous □ □ □ Gants en Chiffon résiné Papier de reporter aux instructions d'assemblage pour des renseignements □...
- Página 19 Conseils de finition de Whittier enduits de finition à base de solvant et d'eau. Lisez et suivez Lisez et suivez les instructions figurant sur l'étiquette. toujours les instructions figurant sur le produit. Mélangez doucement l'enduit de finition; n'agitez pas. Le fait d'agiter peut entraîner la formation de bulles qui seront par la L'aulne est un bois dur et poreux dont l'aspect est souvent suite difficiles à...