JBM 60007 Manual De Instrucciones página 6

Cut depth adjustment
1. Loosen the cutting depth-locking lever.
2. Hold the base plate flat against the body of the work piece
and raise or lower the body of the saw until the blade is at
the right depth.
3. Tighten the depth-locking lever to fix the depth.
Note: For an optimal quality cut, the saw blade should not ex-
tend more than 3 mm below the workpiece.
Cut angle adjustment
1. Loosen the angle-locking knob.
2. Adjust the shoe to the desired angle between 0º and 45º.
3. Tighten the angle-locking knob.
Parallel cut adjustment
1. Loosen the edge guide locking screw.
2. Slide the parallel guide through the slots in the shoe and
adjust to the desired width.
3. Tighten the lock screw to secure it in the position. Ensure
that the edge guide rests against the entire length of the
wood.
OPERATION
Turning On/Off
1. Push the safety lock to either side of the tool.
2. Depress the trigger switch.
3. To stop: release the trigger switch to turn the tool off.
General Cut
1. When starting, always hold the saw handle with one hand
and the front handle with the other hand.
2. Never force the saw, maintain a light and continuous pres-
sure.
PARTS LIST
3. After completing the cut, allow the saw to come to a com-
plete stop.
4. If the cutting is interrupted, resume the cut by allowing the
blade to reach full speed and then reenter the cut slowly.
Pocket Cut
1. Set the depth adjustment based on the thickness of the line
drawing for the cut.
2. Raise the lower guard by using the lower guide lever.
3. With the blade is barely above the material to be cut, start
the saw and allow the blade to attain full speed.
4. Using the front end of the shoe as a pivot point, lower the
blade gradually onto the material which being cut.
5. Release the lower guard when the blade starts to cutting.
6. When the shoe is resting flat on the surface being cut, pro-
ceed cutting in a forward direction to the end of the cut.
7. Allow the blade to come to a full stop before removing it
from the cut.
8. Never pull the saw backward since the blade will climb out
of the cut, as a result, kickback may occur.
Cutting Large Sheets
1. Large sheet or boards require support to prevent from
bending or sags. If you attempt to cut without leveling and
supporting the work piece properly, the blade will tend to
bind or result in kickback.
2. Support the panel or board close to the cut.
3. Be sure to set the blade adjustment so that you can cut
through the material without cutting into the table or wor-
kbench.
MANTENANCE
Always be sure that the tool is switched off and the battery pack
is removed from the tool before attempting to perform inspection
or maintenance.
Regularly clean the tool's air vents with compressed dry air. Do
not attempt to clean by inserting pointed objects through ope-
nings.
Keep cutting tools sharp and clean. Properly maintained tools
with sharp cutting edges are less likely to bind and are easier
to control.
TECHNICAL SPECIFICATIONS
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . DC-20V
Blade Diameter . . . . . . . . . . . . . . . . . . . . .165mm
Arbor size . . . . . . . . . . . . . . . . . . . . . . . . 20mm
No-load Speed . . . . . . . . . . . . . . . . . . . . 4300 RPM
Maximum cutting depth . . . . . . . . 90º: 55mm / 45º: 36mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 3,20kg
NUM.
1
2
3
4
5
6
7
8
9
10
11
· 6 ·
DESCRIPTION
Lever for lower guard
Shoe
Blade clamping screw
Lower guard
Kerf indicator
Angle locking knob
Front handle
Trigger Switch
Trigger Switch lock-off button
Battery release button
Cutting depth-locking lever
REF. 60007