Publicidad
IMPORTANT
Please read
these
instructions carefully before
you
start to assemble this
product
.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these instructions
in
a
safe
place for
future
reference.
Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance on your
product.
Do
not attempt to
assemble the
product
in
windy or wet conditions.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children away from the assembly
area.
When using
a
stepladder or power
tools, make
sure
that you
are
following
the manufacturer's safety advice.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy
snow load on the roof
can make
it unsafe to stand below or nearby.
Do
not
lean
against or push the product during construction.
Hot items
such
as
recently
used
grills, blowtorches etc. must not
be
stored inside the product.
Heavy or sharp articles should
not
be
leaned against the wall panels.
Make Sure
there
are no
hidden pipes or cables
in
the ground before inserting the
pegs
(not supplied)
Do
not touch overhead power
cables
with
the aluminum profiles.
If
color
was
scratched
during
assembly it can be fixed.
Note:
This
product must
be
anchored on to
a
leveled surface and solid
foundation to
ensure
its
stability.
Make sure
that
screws
and anchors
are
compatible with foundation type.
Make sure
that
there
are no
obstructions between the assembly
area
and the final position.
Cleaning Instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Tools &
Equipment
T001
(Supplied)
Before Assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat and leveled.
Choose
a
sunny
area,
away
from overhanging
trees.
Do
not position your product
in an area
exposed to excessive winds.
The
product must
be
positioned and fixed onto
a
flat leveled
surface.
We
strongly recommend to
secure
this product directly onto
a
solid
foundation.
Use
the pre-drilled
holes
in
the
steel base.
Complete
site
preparation before unpacking parts and beginning
assembly.
Sort
the parts and check against the content parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they
do not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the
product.
The
drawings
in
this manual
are
designed for
8'
x
8'
product
+
4' Extension
Kit.
Please
note that content
list refers
only for
8'
x
8'
product.
8'x8'
4'
Ext.
Model
Base
Length
No.
of
Packages
Glory Standard (8'x
8')
244.5 cm
/
96.3"
2
Glory
+ 4' Ext. (8' x 12')
364 cm
/
143.3"
3
Glory
+ 4' Ext. x2
(8'x
16')
483.5 cm
/
190.4"
4
Glory
+ 4' Ext. x3
(8'x
20')
603 cm
/
237.4"
5
Note:
All
the extension module
steps are
marked
with
a
dashed
outline, should
be
performed during the product's assembly
process.
Publicidad
