622540-00,01 D51430
3/24/04
10:50 AM
Page 6
Compressor will be sufficient for tools at all production rates.
Le compresseur peut actionner tout outil, quel que soit le taux de production.
El compresor será suficiente para las herramientas a todo índice de producción.
Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
Le compresseur peut actionner des outils à des taux de production faibles ou modérés, mais peut avoir de la difficulté à
des taux très élevés.
El compresor será suficiente a índices de producción lentos o moderados pero tendrá dificultad con índices demasiado rápi-
dos.
Compressor will be adequate only when tools are utilized at slow production rates (punch-out or occasional use).
Le compresseur ne sera vraiment efficace que lorsque les outils sont utilisés à de faibles taux de production
(p. ex., lors de travaux rapides ou occasionnels).
El compresor será adecuado sólo cuando las herramientas sean utilizadas a índices de producción lentos
(perforación o uso ocasional).
Not Recommended
Taux non recommandés
No se recomienda
FASTENER SPECIFICATIONS
CARACTÉRISTIQUES DES ATTACHES
ESPECIFICACIONES PARA GRAPAS
D51430
Fastener Lengths
(25.4 mm - 50.8 mm)
Longueur
de 25,4 mm – 50,8 mm
(1 à 2 po)
Largos de grapas
1 – 2 pulg.
(25,4 mm – 50,8 mm)
Fastener Gauge
16 gauge
Calibre
Calibre de grapas
Calibre 16
Crown Width
Largeur de tête
11,2 mm (7/16 po)
Ancho de la cabeza
11,2 mm (7/16 pulg.)
Fastener Stick Angle
Straight
Angle du bâton
Ángulo de grapas
Height / Hauteur /Altura
Width / Largeur / Ancho
Length / Longueur / Largo
Weight / Poids / Peso
Recommended Operating Pressure
Pression d'utilisation recommandée
Presión de operación recomendada
Air Consumption per 100 cycles
Consommation d'air par 100 cycles
Consumo de aire por cada 100 ciclos 3.9 scfm @ 100 psi (0,11 scmm a 6,9 bar)
Loading capacity
Capacité de charge
Capacidad de carga
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
Trigger valve housing leaks
Top cap leaks air
Exhaust leaks
Air leaks around nose when
tool is at rest. (Driver blade in up position)
Air leaks around nose when tool is in
actuated position. (Driver blade in
down position)
Tool does not cycle in cold weather
Lack of power; sluggish
Skipping fasteners; intermittent feed
Fasteners jam in tool
D51431
1" - 2"
1" - 2"
(25.4 mm - 50.8 mm)
de 25,4 mm – 50,8 mm
(1 à 2 po)
1 – 2 pulg.
(25,4 mm – 50,8 mm)
16 gauge
16
16
Calibre 16
7/16"
1/2"
13 mm (1/2 po)
13 mm (1/2 pulg.)
Straight
Droit
Droit
Recto
Recto
TOOL SPECIFICATIONS
CARACTÉRISTIQUES DE L'OUTIL
ESPECIFICACIONES DE LA HERRAMIENTA
D51430 16 GA. Medium Crown Stapler
D51430, Agrafeuse pour agrafes à tête moyenne,
calibre 16
D51430 Engrapadora de calibre 16 para
grapas de cabeza mediana
11.0'' (279.4 mm) / 279,4 mm (11,0 po) / 11,0 pulg. (279,4 mm)
3'' (76.2 mm) / 76,2 mm (3 po) / 3 pulg. (76,2 mm)
14.75'' (374.7 mm) / 374,7 mm (14,75 po) / 14,75 pulg. (374,7 mm)
4.5 lbs. (2.04 kg) / 2,04 kg (4,5 lb) / 4,5 lb (2,04 kg)
70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm
2
de 5 à 8,5 kg/cm
(70 à 120 lb/po
70 - 120 psi (4,9 – 8,3 bar, 5 a 8,5 kg/cm
3.9 scfm @ 100 psi
3.9 scfm @ 100 psi (0,11 scmm a 6,9 bar)
Up to 160 fasteners
Jusqu'à 160 attaches
Hasta 160 grapas
Troubleshooting Guide
CONTACT A DEWALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.
DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS
O-ring or valve stem failure
Replace valve using: Trigger Valve Kit: Cat.# D510005
Loose cap screws
Tighten cap screws using appropriate Allen wrench
Damaged or worn gasket or O-ring
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D514301
Main seal or O-ring damaged, debris in tool.
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D514301
Damaged or worn O-rings
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D514301
Damaged or worn bumper
Replace bumper using: Bumper Kit, Cat. # D514303
Tool not receiving air
Check air supply
Valve may be frozen
Warm up tool
Damaged or worn O-rings
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D514301
Broken or damaged driver blade
Replace Driver Blade Kit: Cat. # D514302, D514312
Low air pressure
Check air supply
Lack of lubrication
Lubricate tool using approved pneumatic tool oil.
Damaged or worn O-rings
Replace gasket/O-rings using: O-ring Repair Kit, Cat # D514301
Exhaust port blocked or clogged
Disconnect air, remove exhaust plate from top of tool, clean port
Air restricted
Check air supply and couplers
Lack of lubrication
Lubricate tool using approved pneumatic tool oil
Nosepiece screws loose
Tighten nosepiece screws using appropriate Allen wrench
Wrong size/angle fasteners
Use only recommended fasteners
Dirty magazine
Clean magazine track and nosepiece
Worn magazine
Replace magazine
Broken or damaged driver blade
Replace Driver Blade Kit; Cat. # D514302, D514312
Trigger valve O-ring worn or damaged
Replace valve using: Trigger Valve Kit; Cat. # D510005
Worn piston O-ring
Replace Piston O-Ring using: O-Ring Repair Kit, Cat.# D514301
Worn or damaged pusher spring
Replace spring
Magazine loose
Check that magazine latch is holding firmly
Driver channel in nose piece worn
Replace nosepiece
Wrong size/angle fasteners
Use only recommended fasteners
Magazine loose
Check that magazine screws are holding firmly
Worn driver blade
Replace Driver Blade Kit; Cat # D514302, D514312
Nosepiece screws loose
Tighten nosepiece screws using appropriate Allen wrench
Fasteners not feeding properly
Ensure fasteners are feeding properly into nose
5.5 HP Gas
8 HP Gas
Portable
14 - 16
2 HP Elec.
Handcarry
CFM
8 - 9 CFM
3.2 - 4 CFM
Outil à gaz
Outil à gaz
(5,5 hp)
(8 hp)
Outil élec-
23,8 – 27,2
Petit
trique
CMM
outil
(2 hp)
(14 – 16
portatif
13,6 – 15,3
CFM)
5,4 – 6,8 CMM
CMM
(3,2 – 4 CFM)
(8 - 9 CFM)
8 HP Gas
23,8 – 27,2
5,5 HP Gas
CMM
2 HP Elec.
Portátil
(14 – 16
13,6 – 15,3
5,4 – 6,8 CMM
CFM)
CMM
(3,2 – 4 CFM)
(8 - 9 CFM)
1
2
3
4
5
6
7
8+
2
)
2
ou 4,9 à 8,3 bar)
2
)
Industrial
23+ CFM
Outil indus-
triel
39,1+ CMM
(23+ CFM)
Industrial
39,1+ CMM
(23+ CFM)