Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE:
If the casters
are installed
on your convertible
refrigerator/
freezer, the leveling screws will not work. Shims can be placed
under
the casters
to level a convertible
refrigerator/freezer
that has casters
installed.
Door
Closing
Your convertible
refrigerator/freezer
has two front adjustable
rollers -
one on the right and one on the left. If your convertible
refrigerator/
freezer seems unsteady
or you want the doors to close easier, adjust
the convertible
refrigerator/freezer's
tilt using the instructions
below.
1.
Remove the base grille. See Base Grille graphic
in "Convertible
Refrigerator/Freezer
Doors."
The two leveling screws are part of
the front roller assemblies
which are at the base of the
convertible
refrigerator/freezer
on either side.
2.
Use a screwdriver
to adjust the leveling screws. Turn the leveling
screw to the right to raise that side of the convertible
refrigerator/
freezer or turn the leveling screw to the left to lower that side. It
may take several turns of the leveling screws to adjust the tilt of
the convertible
refrigerator/freezer.
NOTE:
Having someone
push against the top of the convertible
refrigerator/freezer
takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.
PARTS SUPPLIED:
•
Rigid casters
(2)
•
Swivel casters
(2)
•
5/16--18 Self-locking
hex-nuts
(16)
•
5/16-- 18 x %" Hex-head
•
bolts (16)
•
V4-- 20 x 11/4" Lock washers
(4)
V4--20 xl V4" Self-tapping
Hex-head
bolts (4)
Caster
brackets
(located
in
FeaturePak)
(2)
Plastic skids (shipped with
the convertible
refrigerator/
freezer)
1.
Before you begin, turn the lower compartment
control to off.
2.
Unplug
convertible
refrigerator/freezer
or disconnect
power.
3.
Remove
food and any adjustable
shelves and bins from
convertible
refrigerator/freezer.
4.
Open the lower compartment
door and remove the base grille.
Remove the grille by grasping
the grille with both hands, lifting up
and pulling bottom
of the grille toward
you.
5.
Place the plastic skids (shipped
with the convertible
refrigerator/
freezer) on the floor at least 3 ft (91.44 cm) apart. Lay a piece of
cardboard
or other protective
material over the skids. This will
elevate the convertible
refrigerator/freezer
to allow for easier
caster installation
and also protect
it from scratches.
NOTE:
If the skids have been discarded
or are not available,
2" x 4" boards
may be used.
6.
Place the convertible
refrigerator/freezer
on its side on top of the
cardboard
or protective
material.
Make sure the door hinge is
facing upward.
IMPORTANT:
It is important
that the door hinge face upward
during the entire caster installation.
A
B
3.
Open both doors again and check to make sure that they close
as easily as you like. If not, tilt the convertible
refrigerator/freezer
slightly
more to the rear by turning
both leveling screws to the
right. It may take several more turns, and you should
turn both
leveling screws the same amount.
4.
Replace the base grille.
Align
Doors
If the space between
your doors looks uneven, you can adjust it
using the instructions
below:
1.
Pry off the top hinge cover.
2.
Loosen the top hinge screws using a 5/16" socket or wrench.
3.
Have someone
hold the door in place or put a spacer
between
the doors while you tighten
the top hinge screws.
4.
Replace the top hinge cover.
Excessive
Weight
Hazard
Use two or more people
to move
and install
convertible
refrigerator/freezer.
Failure
to do so can result
in back or other
injury.
Gather the required
tools and parts before starting
installation.
TOOLS NEEDED:
•
1/2" Socket
wrench
or nut
•
3/8" Socket
wrench
or nut
driver
driver
•
W' Wrench
o_
A. Top hinge
B. Center hinge
7.
Remove
the casters
and fasteners
from the box.
8.
Locate and remove
the caster brackets
from the FeaturePak.
9.
Using 5/16--18 x %" hex-head
bolts, attach one rigid caster and
one swivel caster to each caster bracket.
The rigid caster fits the
front of the bracket
and the swivel caster fits on the rear.
Publicidad
