Berner BACRHD-1 36V Manual página 18

OBJ_BUCH-2746-001.book Page 18 Wednesday, March 2, 2016 9:47 AM
tually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2009/125/EC (Regulation 1194/2012),
2011/65/EU, until 19 April 2016: 2004/108/EC,
from 20 April 2016 on: 2014/30/EU, 2006/42/EC
including their amendments and complies with the
following standards:
EN 60745-1, EN 60745-2-6, EN 50581.
Technical file (2006/42/EC) at:
Berner Trading Holding GmbH, Bernerstraße 6,
74653 Künzelsau, GERMANY
Armin Hess
Chairman of the Managemant Board
15.01.2016, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
Assembly
Battery Charging (see figure A)
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before us-
ing your power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging by the "Electronic Cell Protection
(ECP)". When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
 Do not continue to press the On/Off switch af-
ter the machine has been automatically
switched off. The battery can be damaged.
Removing the battery
The battery 11 is equipped with two locking levels
that should prevent the battery from falling out
when pushing the battery unlocking button 18 un-
18 | English
intentionally. As long as the battery is inserted in
the power tool, it is held in position by means of a
spring.
To remove the battery 11:
– Push the battery against the base of the power
tool (1.) and at the same time press the battery
unlocking button 18 (2.).
– Pull the battery out of the power tool until a red
stripe becomes visible (3.).
– Press the battery unlocking button 18 again and
pull out the battery completely.
Battery Charge-control Indication
The three green LEDs of the battery charge-control
indicator 20 indicate the charge condition of the
battery 11. For safety reasons, it is only possible to
check the status of the charge condition when the
machine is at a standstill.
– Push button 21 to indicate the charge condition
(also possible when the battery is removed). The
battery charge-control indicator automatically
goes out after approx. 5 seconds.
LED
Continuous lighting 3 x green ≥2/3
Continuous lighting 2 x green ≥1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green
When no LED lights up after pushing button 21,
then the battery is defective and must be replaced.
During the charging procedure, the three green
LEDs light up one after the other and briefly go out.
The battery is fully charged when the three green
LEDs light up continuously. The three LEDs go out
again approx. 5 minutes after the battery has been
fully charged.
Auxiliary Handle
 Operate your machine only with the auxiliary
handle 16.
Changing the position of the auxiliary handle
(see figure B)
The auxiliary handle 16 can be set to any position
for a secure and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 16 in
counterclockwise direction and swivel the auxil-
iary handle 16 to the desired position. Then
Capacity
Reserve
1 609 92A 1SK • 2.3.16