Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Specifications, HPR152i and HPR153i
Frequency Response, -3dB
Frequency Range, -10dB
Maximum Peak SPL
Nominal coverage, H x V
Directivity Index
Directivity Factor
Transducer Description
Acoustic Crossover Freq.
Amp Power
Input Sensitivity
Input Headroom/Clipping
Input Connector/Impedance
Output Connector
Controls, Indicators, and
Adjustments
Protection, Agency certs.
AC Power Requirements
AC Power Connector and Cordset
Dimensions (height, width, depth)
Installation Clearance
Weight
Finish and Grill
Notes:
1- Maximum Peak SPL: Calculated by adding the loudspeaker's sensitivity (1W at 1m) to the peak power (dBw) of the amplifier provided.
2- Directivity Index (DI): Difference between on-axis SPL and average SPL (considering all axes) for the specified coverage range. DI= 10 log Q
3- Directivity Factor (Q): Directivity index expressed as a power ratio Q=10 exp DI/10
4- Amplifier Power: The maximum sustained power at less than 1% clipping, averaged over the intended frequency range,
5- Input Sensitivity: The sine-wave input voltage required to reach amplifier clipping, measured within the frequency range used to determine Maximum Peak SPL, with the gain on "normal" and no gain reduction
due to limiting.
6- Input Headroom/Clipping: Maximum input voltage.
7- Input Connector/Impedance: RF shunt capacitance should not reduce impedance by more than 30% at 20k Hz.
22
HPR152i
54-17.5k Hz
47-20k Hz
135dB
90°x60°
9.4
8.7
15" (381mm) transducer with 3" (76mm) voice coil
1" (25mm) throat compression driver
2,000 Hz
400 Watts, low frequency
100 Watts, high frequency
0.775 V
(+0dBu)
rms
10 V
(+22.2dBu)
rms
XLR female, 22k Ohm, balanced, line-level input
(unbalanced, 11k Ohm)
XLR male, wired in parallel with Input connector
Gain control, 100 Hz low-cut filter switch, Front LED on/off switch, Limit/Clip (red LED), Signal presence (green LED), AC Power (blue LED),
AC Power switch, AC circuit breaker
Thermal limiting, On/Off muting, power limiting, DC protection, short circuit protection, ultrasonic protection, RF protection, UL/CE listed
Factory supplied IEC cordset: 9' (3m) #18AWG 120V North American or European 230V cordset
33.6" (853mm) x 19.1" (485mm) x 17.9" (455mm)
Allow for 6.0" (152mm) of free space behind the enclosure to assure proper amplifier cooling
100 lb/45.4 kg
Wear-resistant textured paint finish on plywood enclosure and powder-coated perforated steel grill
HPR153i
41-17.5k Hz
36-20k Hz
133dB
90°x40°
11.1
12.9
15" (381mm) transducer with 3" (76mm) voice coil
6.5" (165mm) transducer with 1" (25mm) voice coil
1" (25mm) throat compression driver
500 and 2,000 Hz
400 Watts, low frequency
100 Watts, mid frequency
100 Watts, high frequency
0.775 V
(+0dBu)
rms
10 V
(+22.2dBu)
rms
XLR female, 22k Ohm, balanced, line-level input
(unbalanced, 11k Ohm)
XLR male, wired in parallel with Input connector
45.1" (1144mm) x 19.1" (485mm) x 17.9" (455mm)
118 lb/53.5 kg
Publicidad
Tabla de contenido
