Digital Effect Engine - Phonic AM844D USB Manual Del Usuario

Mezcladora con dfx & interfase usb de 8-mic/línea, 4-estéreo 4 grupos
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

32. Solo Button
The Solo button is pushed to allow the
signal of the corresponding channel to
be sent to the Control Room / Phones
mixing bus (pre or post fader, depending
on the properties selected by the pre /
post button, located by the Control Room
/ Phones source buttons), for use with
either headphones or studio monitors.
This button also allows for easier
isolation of individual channel signals,
ensuring setting of the input gain or
tracking of audio by sound engineers is
made simpler. The Peak indicator above
the Solo button also doubles as a Solo
Indicator, illuminating whenever the Solo
function is activated.
33. Channel Level Control (Fader)
This control will alter the signal level that
is sent from the corresponding channel
to the corresponding mixing buses.

Digital Effect Engine

34. Digital Effect Display
This 2-digital numeric display shows the program number that
is currently applied to your EFX audio signal. When you rotate
the Program control, you can scroll through different program
numbers; however the display will revert back to the original
program if a new program is not selected within a few seconds.
For a list of available effects, please observe the Digital Effect
Table.
35. Sig and Clip Indicators
Located within the Digital Effect Display are Clip and Sig LEDs.
The Sig LED will light up when any signal is received by the
effect processor, and the Clip LED will light up shortly before
excessive signals are dynamically clipped. If the Clip LED lights
up too often, it may be advisable to turn down the AUX 3/EFX
control on one or all input channels to ensure the signal level is
not excessive.
36. Program Control
This control is used to scroll through the various effects. Turning
the control clockwise will allow users to ascend into higher
program numbers, and turning it counter-clockwise will allow
users to descend into lower program numbers. Pushing this
control will apply the new effect. When a tap-delay effect is
selected, pressing this control will allow users to select the tap-
delay time.
By pushing the button several times, the effect processor
interprets the time between last two pushes and remembers this
as the delay time – until the button is pushed again. This is kept
even after the power is turned off. When the tap delay effect is
selected, a small LED will flash within the digital effect display
window at the selected intervals.
37. Effect On Button
This button is pushed to turn the corresponding effect panel on
or off. When effects are bypassed, there will be 2 flashing LEDs
in the effect display.
34 35
8
33
32
36
37
Master Section
38. AUX Return 1 and 2 Controls
These controls adjust the signal level of audio fed through to the
29
stereo AUX Return inputs. The "To AUX Send 1" and "To AUX
Send 2" controls adjust the pre-fader level of the signal from the
AUX Return controls to the corresponding AUX mixing buses for
effect-to-monitor sends.
30
39. EFX Return Control
This control adjusts the signal level of audio fed through to stereo
AUX Return 3 inputs. If no device is plugged into the AUX Return
3 inputs, it then acts as the final level control of the built-in Digital
31
Effect Engine.
40. Main L/R - Group Buttons
The first of these buttons changes the destination of the signal
sent from the AUX Return 3 mix between the Main L/R and Group
mix. The second button works when the user selects to send the
signal "To Group", allowing the signal to be sent to either Group
1-2 or Group 3-4.
41. AUX Return 4 Control
This control adjusts the signal level of audio fed through to the
stereo AUX Return 4 inputs. The accompanying "C-R Phones
Only" button allows users to send the signal to the Control Room
/ Phones mixing bus for monitoring purposes.
42. Solo Returns Button
Pushing this buttons allows you to send the signal from all AUX
Returns to solo mixing bus (which is, intern, send to the Control
Room / Phones mixing bus). When the Solo is activated, the
corresponding LED indicator will illuminate.
38
39
43. AUX Send 1 and 2 Master Controls
These controls adjust the final level of the AUX 1 and 2 signals
(as taken from the AUX 1 and 2 level controls on each channel
strip), the audio of which is sent to the AUX 1 and 2 sends. The
corresponding SOLO buttons allow you to send the AUX Send
signal to the Control Room / Phones mixing bus for monitoring
purposes. When either the AUX 1 or AUX 2 solo buttons is
activated, the corresponding LED will illuminate.
43
38
40
42
41
44
AM844D
USB

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Am844d

Tabla de contenido