Declaration Of Conformity; Dust/Chip Extraction - Bosch GBM 1600 RE Professional Instrucciones De Servicio

Vibration total values ah (triax vector sum) and uncertainty
K determined according to EN 60745-2-1:
Drilling into metal: a <2.5m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications
of the tool. However if the tool is used for different
applications, with different accessories or insertion tools
or is poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of
work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with all
relevant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments
and complies with the following standards: EN 60745-1,
EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 03.02.2015
Assembly
u Before any work on the machine itself, pull the
mains plug.
Auxiliary handles (see figure A)
u Operate your machine only with the auxiliary
handles 2 and 4.
Screw the auxiliary handle 2 into the thread 3 on the motor
housing.
The auxiliary handle 4 can be rotated through 360°.
1 600 A00 940 | 2015.03
Manual GBM 1600 RE.indd 19
, K=1.5m/s .
2 2
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Changing the Tool (see figure B)
u Wear protective gloves when changing the tool.
The drill chuck can become very hot during longer work
periods.
Open the key type drill chuck 1 by turning until the tool can
be inserted. Insert the tool.
Insert the chuck key 9 into the corresponding holes of the
key type drill chuck 1 and clamp the tool uniformly.
Replacing the Drill Chuck (see figure C)
Removing the Securing Screw
The key type drill chuck 1 is secured with a securing screw
10 against unintentional loosening. Open the drill chuck 1
completely and unscrew the securing screw 10 by turning
in clockwise direction. Please observe that the securing
screw has a left-hand thread.
If the securing screw 10 is seated tightly, apply a
screwdriver to the screw head and loosen the securing
screw by giving a blow onto the handle of the screwdriver.
Removing the Drill Chuck
To dismount the key type drill chuck 1 position an open-end
spanner (size 17 mm) against the nut on the drive spindle.
Firmly hold the key type drill chuck with one hand and with
the other hand, turn the open-end spanner in anticlockwise
direction until the drill chuck is released from the tapered
drill spindle.
Mounting the Drill Chuck
u Keep the drill spindle taper and the drill hole of the
drill chuck free from grease and debris.
To mount the key type drill chuck 1 turn the nut on the drive
spindle in clockwise direction to the stop. Place the key
type drill chuck without force onto the drive spindle until it
is tightly seated. Apply light blows with a rubber hammer
onto the face side of the key type drill chuck 1 to ensure
tight seating of the chuck. Pay attention that the clamping
jaws of the key type drill chuck do not project, in order not
to damage them.
Mounting the securing screw
Screw the securing screw 10 anticlockwise into the open
key chuck. Always use a new securing screw, as their thread
is applied with a securing adhesive substance, which is
rendered ineffective after several uses.

Dust/Chip Extraction

u Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can
cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.Certain dusts, such
as oak or beech dust, are considered as carcinogenic,
especially in connection with wood-treatment additives
(chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
19
English |
Bosch Power Tools
01/04/15 16:58