Publicidad
Idiomas disponibles
Idiomas disponibles
4
GENERAL INFORMATION (FIG.1)/PAGE 3
4.1
Use of the manual
The manual forms an integral part of the machine and should be
kept for future reference. Please read it carefully before installing/
using the machine. If the machine is sold, the seller must pass on
this manual to the new owner along with the machine.
4.2
Delivery
The machine is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1
Documentation supplied with the machine
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
A4 Warranty regulations
4.3
Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
5
TECHNICAL INFORMATION (FIG.1)/PAGE 3
5.1
Intended use
This machine has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc., to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Inlet water temperature: see machine data plate.
- Inlet water pressure: min. 0.1 MPa - max. 1 MPa.
- Operating ambient temperature: above 0 °C.
The machine is compliant with the IEC 60335-1 and IEC 60335-2-79
standards.
5.2
Operator
The symbol in fig.1 identifies the machine's intended operator.
5.3
Main components
B2 Lance
B3 Trigger gun with safety catch
B4 Power cable
B5 High pressure hose
B7 Oil cap
B8 Diesel tank
B10 Diesel filter
B12 Boiler exhaust
B13 Detergent filter
B14 Parking brake
E
Nozzle
G
Pressure regulator
L
Water filter
V
Water nozzle
Z
Control panel
5.3.1 Accessories (where supplied - see fig.1)
C3
Handle
C9
Adaptor
C10 Screws
C11 Brackets
C12 Lever
C14 Wheels
C16 Pressure gauge
5.3.2
Control panel (see fig.1)
- Machine switch (H)
OFF/0 - ON/I Cold water operation.
- Hot water operation switch (T)
0/OFF - ON/I Hot water operation.
- Temperature setting thermostat (Y) for hot water operation.
C18 Diesel level warning light
C21 Power on light
C22 Power on light boiler
- Diesel level warning light (C18)
- Power on light (C21)
- Power on light boiler (C22)
5.4
Safety devices
- Starter device (H)
The starter device prevents accidental use of the machine.
- Boiler starter device (T)
The starter device prevents accidental use of the boiler.
- Lack of water device
The device prevents the boiler from operating without water.
Warning - danger!
Do not tamper with or adjust the safety valve setting.
- Safety and/or relief valve.
The safety valve is also a relief valve.
- Safety catch (D): prevents accidental emission of water jet.
- Thermal protector: stops the machine in case of overload.
- Magneto-thermic switch: cuts out the machine in case of over-
load.
6
INSTALLATION (FIG.2)/PAGE 4
6.1
Assembly
Warning - danger!
All installation and assembly operations must be per-
formed with the machine disconnected from the mains power
supply.
The assembly sequence is illustrated in fig.2.
6.2
Fitting the rotary nozzle
(For models with this feature).
The rotary nozzle kit delivers greater washing power.
Use of the rotary nozzle may cause a reduction in pressure of 25%
compared to the pressure obtained with the adjustable spray
nozzle. However, the rotary nozzle delivers greater washing power
due to the rotation of the water jet.
6.3
Electrical connection
Warning - danger!
Check that the electrical supply voltage and frequency
(V-Hz) correspond to those specified on the data plate (fig.2).
6.3.1
Use of extension cables
The cross-section of the extension cable should be pro-
portional to its length; the longer it is, the greater its
cross-section should be. See table I.
6.4
Water supply connection
Warning - danger!
Only clean or filtered water should be supplied to the
machine. The flow rate of the water inlet tap must be equal
to that of the pump.
Place the machine as close to the water supply system as possible.
6.4.1
Connection points
l Water outlet (OUTLET)
n Water inlet with filter (INLET)
6.4.2
Connection to the mains water supply
The machine may only be connected directly to the
mains drinking water supply if the supply hose is fitted
with a backflow preventer valve with drain facility as per
current regulations in force. Make sure that the hose is at
least Ø 13 mm, that it is reinforced and that it is not more
than 25 m long.
13
English
EN
Publicidad
