Makita DUA301 Manual De Instrucciones página 15

19. Before cutting limbs, keep an escape area
away from the falling limb. First, clear
obstructs such as limbs and branches from
the work area. Move all tools and goods from
the escape area to another safe place.
20. Before cutting branches and limbs, check
the falling direction of them, considering the
condition of branches and limbs, adjoining
trees, wind direction, etc. Pay full attention to
the falling direction, and the rebound of the
branch, which hit the ground.
21. Never hold the tool at an angle of more than
60°. Otherwise falling objects can hit the oper-
ator and cause serious injury. Never stand
underneath the limb being cut.
22. Pay attention to broken or bent branches. They may
bounce back in cutting, causing unexpected injury.
23. Before cutting limbs that you intend to cut,
remove branches and leaves around them.
Otherwise the saw chain may be caught by them.
24. To prevent the saw chain from being caught in
the kerf, do not release the lever before pulling
the saw chain out of the kerf.
25. If the saw chain is bound in the kerf, immedi-
ately stop the tool, carefully move the branch
to open the kerf and release the saw chain.
26. Avoid kickback (rotational reactive force
towards the operator). To prevent kickback,
never use the guide bar nose or perform a
penetrating cut. Always beware of the position
of the guide bar nose.
27. Check the chain tension frequently. When
checking or adjusting the chain tension,
switch off the tool and remove the battery
cartridge. If the tension is loose, tighten it.
Vibration
1. Exposing to excessive vibration injures blood
vessels or nervous system of the operator and
causes the following symptoms in the fingers,
hands or wrists: "Falling asleep" (numbness),
tingling, pain, stabbing sensation, or alteration
of skin color or of the skin. If any of these
symptoms occur, see a physician.
To reduce the risk of "white finger disease",
keep your hands warm during operation and
well maintain the tool and accessories.
For operating time, follow your local regula-
tions or physician's advice.
Transport
1. Before transporting the tool, switch off the tool
and remove the battery cartridge. Always fit
the guide bar cover during transportation.
When transporting the tool, carry it in a hori-
2.
zontal position by holding the grip.
Maintenance
Have your equipment serviced by our autho-
1.
rized service center, always using only genu-
ine replacement parts. Incorrect repair and poor
maintenance can shorten the life of the tool and
increase the risk of accidents.
2. Before doing any maintenance or repair work
or cleaning the tool, always switch off the tool
and remove the battery cartridge. Wait until the
tool cools down.
3. Always wear protective gloves when handling
the saw chain.
4. After each use, tighten all screws and nuts,
except for adjustment screws.
Keep the saw chain sharp. If the saw chain
5.
has become blunt and cutting performance is
poor, ask Makita authorized service center to
sharpen it or replace it with new one.
6. Do not attempt any maintenance or repair
not described in this instruction manual. Ask
Makita authorized service center for such
work.
7. Always use Makita genuine spare parts and
accessories only. Using parts or accessories
supplied by a third party may result in the tool
breakdown, property damage and/or serious
injury.
Storage
1. Before storing the tool, perform full cleaning
and maintenance. Fit the guide bar cover.
Remove the battery cartridge. Drain the chain
oil after the tool cools down.
Store the tool in a dry and high or locked loca-
2.
tion out of reach of children.
3. Do not prop the tool against something, such
as a wall. Otherwise it may fall suddenly and
cause an injury.
Electrical and battery safety
1. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
2. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
3. Do not charge battery in rain, or in wet
locations.
4. Do not charge the battery outdoors.
5. Do not handle charger, including charger plug,
and charger terminals with wet hands.
Avoid dangerous environment. Don't use the
6.
tool in damp or wet locations or expose it to
rain. Water entering the tool will increase the
risk of electric shock.
SAVE THESE INSTRUCTIONS.
WARNING:
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
Before using battery cartridge, read all instruc-
1.
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper with the battery
cartridge. It may result in a fire, excessive heat,
or explosion.
15 ENGLISH
DO NOT let comfort or familiarity