Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS
C-ACC-EB-8W-KIT-UL Series
EMERGENCY DRIVER CHECK
(FOR LUMINAIRES EQUIPPED WITH
EMERGENCY DRIVER)
NOTE: Emergency driver and AC driver must be fed from the same
branch circuit.
NOTE: For short-term testing of the emergency function, the battery
must be charged for at least one hour. The emergency driver must be
charged for at least 24 hours before conducting a long-term test.
STEP 1:
When AC power is applied, the charging indicator light is illuminated,
indicating the battery is being charged. When power fails, the
emergency driver automatically switches to emergency power, operating
the LED array. When AC power is restored, the emergency driver
returns to the charging mode.
STEP 2:
Although no routine maintenance is required to keep the emergency
driver functional, it should be checked periodically to ensure that it is
working. The following schedule is recommended:
• Visually inspect the charging indicator light monthly. It should be
illuminated.
• Test the emergency operation of the fixture at 30-day intervals for
a minimum of 30 seconds. When the test switch is depressed, the
LED array should operate.
• Conduct a 90-minute discharge test once a year. The LED array
should operate for at least 90 minutes.
If the luminaire fails any of these checks, consult service personnel.
REFER ANY SERVICING INDICATED BY THESE CHECKS TO
QUALIFIED PERSONNEL
EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE
SAME BRANCH CIRCUIT.
NOTE: Fixture is equipped with universal volt AC driver and emergency
driver 120-277V (ie. 120V, 208V, 240V or 277V)
NOTE: The emergency driver must be fed from the same branch as the
AC driver.
Make the following electrical connections:
a. Connect the black luminaire lead labeled switched
to the switched voltage supply lead.
b. Connect the black emergency driver lead labeled
unswitched to the unswitched voltage supply lead.
c. Connect the white emergency driver lead to
the LED driver white lead and supply neutral
lead (HOT 2 for 208/240V wiring).
d. Connect the back box ground (green)
lead to the supply ground lead.
ELECTRICAL CONNECTIONS
http://lighting.cree.com/warranty
Document:
LPN05498X0001A0_B
Created By:
TMT
FCC NOTICE
CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved could void
your authority to use this equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
CAN ICES-005 (B)/NMB-005 (B)
NEUTRAL OR
SWITCHED HOT
UNSWITCHED HOT
|
1-800-236-6800
Date
3-6-2023
LUMINAIRE
GROUND
GREEN/YELLOW
WHITE (EM DRIVER)
HOT 2
WHITE
(LED DRIVER)
BLACK SWITCHED
BLACK
UNSWITCHED
Publicidad
